repairing an electric guitar body

If you have a string instrument of any kind that needs fixing, a mistake you made in building a new instrument that you need to "disappear," or a question about the ethics of altering an older instrument, ask here. Please note that it will be much easier for us to help you decide on the best repair method if you post some pictures of the problem.

repairing an electric guitar body

Postby Barry Catlin » Thu Aug 30, 2012 10:57 am

Hi retied carpenter joiner with wood machine know how - here
i have a encore blaster in need of a re-fur'bish
its just a thought but has any one ever reduced the size of the neck
to make it more ( short finger ) player friendly.
if so how much would it be practical to remove considering the load / stress
when the strings are on.
or am i "nuts" to even think of doing it.
I would appreciate any input thanks
Barry Catlin
 
Posts: 2
Joined: Wed Aug 29, 2012 7:54 am

Re: repairing an electric guitar body

Postby Chris Reed » Thu Aug 30, 2012 1:34 pm

Shorter neck = different fret spacing (i.e. replace fretboard), probably different tuning (unless you can find strings for the shorter scale), maybe moving the bridge, shortening the truss rod (if there is one).

Apart from that ...

Edit Did you mean to make the neck thinner front to back? That might be doable, but you have to stop well before you hit the truss rod (hidden inside the neck, but where?).

If you want to reduce it side-to-side that wouldn't cause structural problems, though it would look odd.
Chris Reed
 
Posts: 155
Joined: Thu Feb 02, 2012 6:26 pm

Re: repairing an electric guitar body

Postby Alain Lambert » Thu Aug 30, 2012 2:33 pm

The published specs for this guitar is 43mm (1" 11/16) neck width and 34 mm ( 1" 7/16) string spacing, which is OK to me.
The scale length is 25.5 ".
You may be able to change a little bit the neck profile at the back to make it more comfortable, but that's about it. Like Chris mentionned, you should be sure not to hit the truss rod channel, this link: http://www.google.ca/search?q=fender+ne ... 76&bih=926 will give you some examples. If you do it, try not to touch the thick ness of the neck, so you do not hit the truss rod pocket.
Alain Lambert
 
Posts: 82
Joined: Sat Jan 07, 2012 7:18 pm
Location: Trois-Rivieres, Quebec

Re: repairing an electric guitar body

Postby Clay Schaeffer » Fri Aug 31, 2012 8:45 am

If it is a bolt on neck you might consider making an entirely new neck for it. This would allow you to change the scale length and neck width/thickness with less trouble than modifying the old neck.
Clay Schaeffer
 
Posts: 1340
Joined: Fri Jan 06, 2012 12:04 pm

Re: repairing an electric guitar body

Postby Barry Catlin » Wed Sep 05, 2012 4:02 pm

HI Chris and Alain

Just to say thanks for your input

chris i did mean make it thinner if the truss rod will allow
or even run a small flute mould down both sides,
will let you know the results of my project

barry

ps thanks for the link
Barry Catlin
 
Posts: 2
Joined: Wed Aug 29, 2012 7:54 am


Return to String Instrument Repair: Practical and Political Issues

Who is online

Users browsing this forum: No registered users and 1 guest

Your purchase from these sites helps support the MIMForum, but only if you start at the links below!!!
Amazon music     Amazon books     Amazon tools     Rockler tools     Office Depot    

The MIMF is a member-supported forum, please consider supporting us with a donation, thanks!
 • Book store • Tool store • Links •