$100 Local Materials Challenge, Eddie McRae, Grand Auditorium Cutaway Acoustic

Here is where you put your entries.

Re: $100 Local Materials Challenge, Eddie McRae, Grand Auditorium Cutaway Acoustic

Postby Mark Swanson » Mon May 07, 2012 11:48 pm

Hmmm, I can only make guesses from here! But you have loosened up the top with the scalloping. The missing arch may pull up a bit with the string tension but you won't know that until you string it. I think that when the braces are made looser, they tend to want to flatten a bit, if that makes sense....that's the only thing I can think of, other than I have had that happen to me as well and I just dealt with it by properly setting the neck. After that I had no troubles.
Was your bracewood well-dried and all setttled down?
    Mark Swanson, guitarist, MIMForum Staff
User avatar
Mark Swanson
 
Posts: 1910
Joined: Thu Jan 05, 2012 11:11 am
Location: Grand Rapids, Michigan USA

Re: $100 Local Materials Challenge, Eddie McRae, Grand Auditorium Cutaway Acoustic

Postby Eddie McRae » Thu May 10, 2012 6:45 pm

Thanks Mark. The bracewood came from some spruce that's been in the shop for at least 10 years so it's well dried, no doubt. I tend to think the scalloping was probably the reason. At any rate, I resolved the issue but it took a little time to do so. I normally don't like to cut the neck angle until after the body is complete so I can actually take a physical measurement, but in this case, I was trying to make up time.
User avatar
Eddie McRae
 
Posts: 153
Joined: Thu Feb 23, 2012 10:07 am
Location: Woodbury, GA USA

Re: $100 Local Materials Challenge, Eddie McRae, Grand Auditorium Cutaway Acoustic

Postby Eddie McRae » Thu May 10, 2012 6:49 pm

I got the necks fitted on both. I'd already made both bridges earlier but I decided to go ahead and make a couple of black walnut pickguards and then mocked everything up just to get an idea of the outcome. Still not sure about the pickguards....can't decide if I like them or not.
Attachments
GAC92.JPG
GAC93.JPG
User avatar
Eddie McRae
 
Posts: 153
Joined: Thu Feb 23, 2012 10:07 am
Location: Woodbury, GA USA

Re: $100 Local Materials Challenge, Eddie McRae, Grand Auditorium Cutaway Acoustic

Postby Josh Humphrey » Thu May 10, 2012 11:10 pm

I love the pickguards! Long live black walnut.
Josh Humphrey
 
Posts: 55
Joined: Sat Jan 07, 2012 6:23 pm

Re: $100 Local Materials Challenge, Eddie McRae, Grand Auditorium Cutaway Acoustic

Postby Jason Rodgers » Fri May 11, 2012 12:03 am

Josh Humphrey wrote:I love the pickguards! Long live black walnut.


Yup! Keep em!
-Ruining perfectly good wood, one day at a time.
Jason Rodgers
 
Posts: 1542
Joined: Fri Jan 06, 2012 4:05 pm
Location: Portland, OR

Re: $100 Local Materials Challenge, Eddie McRae, Grand Auditorium Cutaway Acoustic

Postby Tristan Williams » Sun May 13, 2012 8:43 am

Lovely!
Tristan Williams
 
Posts: 100
Joined: Thu Feb 02, 2012 11:10 am
Location: Espoo, Finland

Re: $100 Local Materials Challenge, Eddie McRae, Grand Auditorium Cutaway Acoustic

Postby david frassetto » Sun May 13, 2012 6:01 pm

+1 on keeping the pickguards.
Lap steel fanatic
User avatar
david frassetto
 
Posts: 78
Joined: Wed Mar 07, 2012 2:55 pm
Location: Milwaukee WI

Re: $100 Local Materials Challenge, Eddie McRae, Grand Auditorium Cutaway Acoustic

Postby Eddie McRae » Mon May 14, 2012 7:36 pm

Thanks. I've grown to like the pickguards the more I've looked at them. I did manage to get the necks carved over the weekend and got started with the purfling and binding work today. Hoping to be done with the construction work on these by Wednesday and from there, it'll just be finish work. Needless to say....I guess it's pretty safe to say now that I won't be making that deadline. They'll be built but they won't be finished.
User avatar
Eddie McRae
 
Posts: 153
Joined: Thu Feb 23, 2012 10:07 am
Location: Woodbury, GA USA

Re: $100 Local Materials Challenge, Eddie McRae, Grand Auditorium Cutaway Acoustic

Postby Eddie McRae » Thu May 17, 2012 8:52 pm

Glued bridges....
Attachments
GAC103.JPG
GAC104.JPG
User avatar
Eddie McRae
 
Posts: 153
Joined: Thu Feb 23, 2012 10:07 am
Location: Woodbury, GA USA

Re: $100 Local Materials Challenge, Eddie McRae, Grand Auditorium Cutaway Acoustic

Postby Eddie McRae » Thu May 17, 2012 8:54 pm

Finished up with neck attachment system....
Attachments
GAC105.JPG
GAC106.JPG
User avatar
Eddie McRae
 
Posts: 153
Joined: Thu Feb 23, 2012 10:07 am
Location: Woodbury, GA USA

Re: $100 Local Materials Challenge, Eddie McRae, Grand Auditorium Cutaway Acoustic

Postby Eddie McRae » Thu May 17, 2012 9:05 pm

Both are complete now as far as construction goes. All that's left is finish work and then setup. This is a pic of one of them bolted back together.
Attachments
GAC102.JPG
User avatar
Eddie McRae
 
Posts: 153
Joined: Thu Feb 23, 2012 10:07 am
Location: Woodbury, GA USA

Re: $100 Local Materials Challenge, Eddie McRae, Grand Auditorium Cutaway Acoustic

Postby Jason Rodgers » Thu May 17, 2012 10:20 pm

This thing is gonna have some tasty color under finish!

Can you give a side pic of the neck joint? Specifically, once that button is locked into its hole, what's the rest of the fretboard extension doing: flush with the top or floating just a little?
-Ruining perfectly good wood, one day at a time.
Jason Rodgers
 
Posts: 1542
Joined: Fri Jan 06, 2012 4:05 pm
Location: Portland, OR

Re: $100 Local Materials Challenge, Eddie McRae, Grand Auditorium Cutaway Acoustic

Postby Eddie McRae » Thu May 17, 2012 10:37 pm

The fretboard extension mount has an 8-32 threaded insert in it. A cap screw is threaded from the inside of the body through the fretboard support and into the mount. It pulls the fretboard down tight and flush to the top. The complete system consists of the 2 heel bolts (1/4-20 cap screws) and the fretboard bolt (8-32 cap screw). I generally like to place the mount further down towards the end of the fretboard but because of the upper bout brace, I wasn't able to extend the support that far.
User avatar
Eddie McRae
 
Posts: 153
Joined: Thu Feb 23, 2012 10:07 am
Location: Woodbury, GA USA

Re: $100 Local Materials Challenge, Eddie McRae, Grand Auditorium Cutaway Acoustic

Postby Josh Humphrey » Fri May 18, 2012 1:47 am

Neat idea! I would worry about vibration in the unsupported area- do you supplement with any glue?
Josh Humphrey
 
Posts: 55
Joined: Sat Jan 07, 2012 6:23 pm

Re: $100 Local Materials Challenge, Eddie McRae, Grand Auditorium Cutaway Acoustic

Postby Eddie McRae » Fri May 18, 2012 5:01 am

I've never used any glue with this system. I've built 11 acoustics and resonators using this setup and haven't had the slightest problem with any of them. However, as I said above, I generally place the mount directly under the 19th dot inlay but in this case because of the location of the upper bout brace, I wasn't able to extend the support that far. So I had to place the mount under the 17th instead. In the future, I may eliminate the upper bout brace on this model. The solid fretboard support under the soundboard should adequately support the top without the need of that brace and it would allow me to place the mount closer to the end of the fretboard.
User avatar
Eddie McRae
 
Posts: 153
Joined: Thu Feb 23, 2012 10:07 am
Location: Woodbury, GA USA

Re: $100 Local Materials Challenge, Eddie McRae, Grand Auditorium Cutaway Acoustic

Postby Eddie McRae » Fri May 18, 2012 4:35 pm

As requested....a couple of close-up pics of the fretboard extension and it's fit.
Attachments
GAC108.JPG
GAC107.JPG
User avatar
Eddie McRae
 
Posts: 153
Joined: Thu Feb 23, 2012 10:07 am
Location: Woodbury, GA USA

Re: $100 Local Materials Challenge, Eddie McRae, Grand Auditorium Cutaway Acoustic

Postby Eddie McRae » Fri May 18, 2012 4:38 pm

Construction work is complete on both. So now it's time for some finish work. I'll most likely start spraying seal coats on them over the weekend but I certainly won't be making the challenge deadline.
Attachments
GAC109.JPG
GAC110.JPG
User avatar
Eddie McRae
 
Posts: 153
Joined: Thu Feb 23, 2012 10:07 am
Location: Woodbury, GA USA

Re: $100 Local Materials Challenge, Eddie McRae, Grand Auditorium Cutaway Acoustic

Postby Mark Swanson » Fri May 18, 2012 11:29 pm

That's a couple of nice lookin' guitars Eddie!
    Mark Swanson, guitarist, MIMForum Staff
User avatar
Mark Swanson
 
Posts: 1910
Joined: Thu Jan 05, 2012 11:11 am
Location: Grand Rapids, Michigan USA

Re: $100 Local Materials Challenge, Eddie McRae, Grand Auditorium Cutaway Acoustic

Postby Eddie McRae » Sat May 19, 2012 2:26 pm

Thanks Mark. These 2 acoustics, along with a custom cherry LP that I've just finished up with, will all be getting nitro burst finishes. I'm looking forward to getting them setup to hear how they sound. I'll post pictures of them when they're done.
User avatar
Eddie McRae
 
Posts: 153
Joined: Thu Feb 23, 2012 10:07 am
Location: Woodbury, GA USA

Re: $100 Local Materials Challenge, Eddie McRae, Grand Auditorium Cutaway Acoustic

Postby Matthew Lau » Sun May 27, 2012 2:13 am

Tasty!
Matthew Lau
 
Posts: 346
Joined: Sat Feb 18, 2012 2:03 am

PreviousNext

Return to The Local Materials Challenge (Closed)

Who is online

Users browsing this forum: No registered users and 1 guest

Your purchase from these sites helps support the MIMForum, but only if you start at the links below!!!
Amazon music     Amazon books     Amazon tools     Rockler tools     Office Depot    

The MIMF is a member-supported forum, please consider supporting us with a donation, thanks!
 • Book store • Tool store • Links •