Neck Rebuild

If you have a string instrument of any kind that needs fixing, a mistake you made in building a new instrument that you need to "disappear," or a question about the ethics of altering an older instrument, ask here. Please note that it will be much easier for us to help you decide on the best repair method if you post some pictures of the problem.

Neck Rebuild

Postby Gordon Bellerose » Tue Mar 12, 2019 10:33 pm

One of my customers brought in a 1980's Aria Pro that had a worn out fret board and a broken truss rod.
He is somewhat of a collector of these guitars, and desperately wanted to repair the neck.

After removing the fret board and cleaning the surface, I removed the old truss rod.
This thing was 15/32 wide and 23/64 deep, and had rounded corners on the bottom.
Old Truss Rod.jpg


I had to rout the channel so it had square corners on the bottom, to be able to fit a solid piece of maple into it, to fill it.
I took a few notes from Barry Daniels post where he designed a jig to rout a new truss rod channel, and rout for carbon fiber rods.
I made up this jig that utilizes my Veritas tool guide.
Here is a shot of the bottom where the neck gets clamped.
Neck Routing Jib Bottom.jpg


Here is a shot of the top with the tool guide and home made router base.
Neck Routing Jig Top 1.jpg
I need your help. I can't possibly make all the mistakes myself!
Gordon Bellerose
 
Posts: 1141
Joined: Wed May 30, 2012 11:47 pm
Location: Edmonton AB. Canada

Re: Neck Rebuild

Postby Gordon Bellerose » Tue Mar 12, 2019 10:35 pm

Here is the neck after routing.
Neck After Routing.jpg


And here it is with the new channel filled. Just a bit of sanding to level it.
Then it's on to routing the new narrower (1/4 inch) truss rod channel.
Channel Filled.jpg
I need your help. I can't possibly make all the mistakes myself!
Gordon Bellerose
 
Posts: 1141
Joined: Wed May 30, 2012 11:47 pm
Location: Edmonton AB. Canada

Re: Neck Rebuild

Postby Brian Evans » Wed Mar 13, 2019 7:57 am

Nice jig creation, I cut all my truss rod slots on the table saw, which obviously would also need significant jig work. I need to embrace the router more, but they scare the heck out of me.
Brian Evans
 
Posts: 776
Joined: Sat Aug 30, 2014 8:26 am
Location: Tatamagouche, Nova Scotia

Re: Neck Rebuild

Postby Gordon Bellerose » Wed Mar 13, 2019 1:07 pm

Brian,

Once you have a proper jig and a way to really control the router, such as this guide, routers are not so scary.

I like this jig as it allows me to work on necks that are already built.
On a neck that is under construction, it has been easier to use a router table.
Now that I have this jig, I can use it for either; and it makes it easy to rout for carbon fiber rods also.

I built the removable stand tall enough that I can put an acoustic neck into the jig, and long enough to do a bass neck.
I need your help. I can't possibly make all the mistakes myself!
Gordon Bellerose
 
Posts: 1141
Joined: Wed May 30, 2012 11:47 pm
Location: Edmonton AB. Canada

Re: Neck Rebuild

Postby Bill Raymond » Wed Mar 13, 2019 7:46 pm

I need to embrace the router more, but they scare the heck out of me.


And tablesaws don't?
Bill Raymond
 
Posts: 353
Joined: Fri Jan 06, 2012 5:37 pm
Location: Red Bluff California

Re: Neck Rebuild

Postby Gordon Bellerose » Wed Mar 13, 2019 10:26 pm

I believe I mentioned above that "I took a few notes" from Barry Daniels.

Actually this jig is based directly off of Barry's design, and I need to acknowledge him for that.
I need your help. I can't possibly make all the mistakes myself!
Gordon Bellerose
 
Posts: 1141
Joined: Wed May 30, 2012 11:47 pm
Location: Edmonton AB. Canada

Re: Neck Rebuild

Postby Steve Sawyer » Thu Mar 14, 2019 11:39 am

Brian Evans wrote:Nice jig creation, I cut all my truss rod slots on the table saw, which obviously would also need significant jig work. I need to embrace the router more, but they scare the heck out of me.

Let me echo Gordon's comment. A gude for the router as pictured is a huge game-changer. I discovered guided routing a few years ago, and I was amazed at the confidence it lends to the operator and the quality of the results.

Gordon - whose guide system are you using there? That looks really nice!!
==Steve==
User avatar
Steve Sawyer
 
Posts: 732
Joined: Wed Jan 02, 2013 2:20 pm
Location: Detroit, Michigan

Re: Neck Rebuild

Postby Gordon Bellerose » Thu Mar 14, 2019 12:50 pm

That is the Veritas Edge Guide system sold by Lee Valley.

It has distance stops that are easily adjustable also. It clamps to the edge of the surface plywood.

I made the router base from a small piece of lexan, but you could use plywood if you wanted.
I need your help. I can't possibly make all the mistakes myself!
Gordon Bellerose
 
Posts: 1141
Joined: Wed May 30, 2012 11:47 pm
Location: Edmonton AB. Canada

Re: Neck Rebuild

Postby Barry Daniels » Fri Mar 15, 2019 4:55 pm

If I was to build this jig again, I would add an edge guide with an added axis of adjustment.

https://www.rockler.com/rockler-perfect-fit-dado-jig
MIMF Staff
Barry Daniels
 
Posts: 2160
Joined: Thu Jan 05, 2012 10:58 am
Location: The Woodlands, Texas


Return to String Instrument Repair: Practical and Political Issues

Who is online

Users browsing this forum: No registered users and 2 guests

Your purchase from these sites helps support the MIMForum, but only if you start at the links below!!!
Amazon music     Amazon books     Amazon tools     Rockler tools     Office Depot    

The MIMF is a member-supported forum, please consider supporting us with a donation, thanks!
 • Book store • Tool store • Links • 
cron