Bondic UV light curing glue

TEST ON SCRAP FIRST! If your question is about repair work, either regluing or refinishing, please post it in our Repair Section.

Bondic UV light curing glue

Postby Chris Mudd » Mon Oct 24, 2016 12:33 pm

Han anyone tried any products like "Bondic"?

these are the UV light curing glues that are being advertised right now.

I could think of a million places it could be handy, but I was raised with a dis-trust of the "As Advertised on TV" stuff.

Chris
Chris Mudd
 
Posts: 21
Joined: Sun Jul 15, 2012 6:12 pm

Re: Bondic UV light curing glue

Postby David King » Mon Oct 24, 2016 2:42 pm

Looks like an epoxy monomer with UV initiator. These materials have been around for decades and widely used in the dental, nail salon, printing and windshield repair industries. The stuff I have experience with is a for encapsulation called a doming epoxy. It cures with small 4w UV fluorescent bulbs or in direct sunlight. It's very clear and very hard but it doesn't stick to wood particularly well. Any of the material that soaks into the wood grain won't cure and eventually causes the stuff to delaminate. Its takes a lot longer than 4 seconds so I'm doubtful that an LED can put out the W/m2 to accomplish that. The composite that dentists use is opaque white so that must slow down the cure though they do multiple thin layers with between 30 seconds and 2 minutes of curing time.
David King
 
Posts: 2615
Joined: Sat Jan 07, 2012 10:01 pm
Location: Portland, OR

Re: Bondic UV light curing glue

Postby Peter Wilcox » Fri Sep 13, 2019 3:02 pm

Anybody have experience with this stuff since these posts, not necessarily instrument related?
Maybe I can't fix it, but I can fix it so no one can fix it
User avatar
Peter Wilcox
 
Posts: 1050
Joined: Sun Jan 08, 2012 1:31 am
Location: Northeastern California

Re: Bondic UV light curing glue

Postby John Tuttle » Tue Sep 17, 2019 1:28 pm

I use Bondic and other UV light-cured glued in technology repairs. It's great for surface coverage and protection applications and cable abrasion repair. successive layers can be applied after curing to build body and I haven't witnessed delamination in that scenario. Incomplete curing causes issues when you can't get good light penetration to AL of the applied Bodic solution. So, you're not going to be able to use it for gluing one part to another, at least not with the stuff I've used. It's great for cable and solder joint protection and is extremely abrasion resistant. I'll apply a drop or two to cover a solder joint at the circuit board of an endpin jack circuit board connection for a bridge pickup wire. I've also used it to secure a wire to the inside of a guitar and had marginal success. As previously stated, if it soaks into the wood, it won't cure properly and then has poor adhesion. I have spread a thin layer across a path of wood with my finger and then quickly cured it to create a base layer which I then stuck an upper layer to and that seemed to work better. In general, I stopped using it for guitars as it really wasn't "a better mousetrap"
User avatar
John Tuttle
 
Posts: 14
Joined: Sun Jan 08, 2012 12:16 pm

Re: Bondic UV light curing glue

Postby David King » Tue Sep 17, 2019 1:49 pm

I really don't see much use for them besides repairing a nut of historic value that's too low with a matching color.
David King
 
Posts: 2615
Joined: Sat Jan 07, 2012 10:01 pm
Location: Portland, OR


Return to Glues and Finishes

Who is online

Users browsing this forum: No registered users and 0 guests

Your purchase from these sites helps support the MIMForum, but only if you start at the links below!!!
Amazon music     Amazon books     Amazon tools     Rockler tools     Office Depot    

The MIMF is a member-supported forum, please consider supporting us with a donation, thanks!
 • Book store • Tool store • Links • 
cron