Volute shape

Please put your pickup/wiring discussions in the Electronics section; and put discussions about repair issues, including "disappearing" errors in new instruments, in the Repairs section.
Post Reply
User avatar
Steve Sawyer
Posts: 938
Joined: Wed Jan 02, 2013 2:20 pm
Location: Detroit, Michigan

Volute shape

Post by Steve Sawyer »

I just finished carving my first volute in this Lester I’m building. Seems to be in a good spot, but I’ve never played a guitar with one, and don’t have another to compare to. When fingering a 1st-fret barre (F or Bb), my thumb sits right at the transition from neck shaft to volute. It seems to feel ok - not “in the way” - but not being fretted or strung, I thought I’d ask if that sounds right.

Thanks.
==Steve==

User avatar
Barry Daniels
Posts: 2676
Joined: Thu Jan 05, 2012 10:58 am
Location: The Woodlands, Texas

Re: Volute shape

Post by Barry Daniels »

I usually put the peak of the volute right behind the nut.
MIMF Staff

John Clifford
Posts: 180
Joined: Mon Dec 18, 2017 3:08 pm

Re: Volute shape

Post by John Clifford »

Here's what my '70s Les Paul Deluxe looks like. I'm not sure I would copy this shape if I was making one, and I don't think it needs to be that far back. But I agree that the crest of the volute should be at or behind the nut line.
Attachments
Les Paul.jpg

User avatar
Peter Wilcox
Posts: 1176
Joined: Sun Jan 08, 2012 1:31 am
Location: Northeastern California

Re: Volute shape

Post by Peter Wilcox »

Gibson may not be the best example of how to design a neck. :lol:

I put the crest of the volute at the nut, figuring (possibly erroneously) that is the weakest point - the narrowest and with the maximum excavation for the truss rod access (at least the way I make it.) Also, most of my instruments have a zero fret, which in essence puts the volute a little farther back. I'm not much of a player, but when I barre an F or Bb my thumb is basically mid fret, where the forward part of the volute has ended.
Maybe I can't fix it, but I can fix it so no one can fix it

User avatar
Barry Daniels
Posts: 2676
Joined: Thu Jan 05, 2012 10:58 am
Location: The Woodlands, Texas

Re: Volute shape

Post by Barry Daniels »

Holy cow! I think we have stumbled upon a consensus. This may be the first occurrence on the internet.
MIMF Staff

User avatar
Steve Sawyer
Posts: 938
Joined: Wed Jan 02, 2013 2:20 pm
Location: Detroit, Michigan

Re: Volute shape

Post by Steve Sawyer »

Thank folks. I too put the crest right at the nut. Just trying to gauge whether the slope to the shaft is too long. From that side view above, it looks like I’m in good shape.

Glad I could ask a question leading to such an historic internet milestone!! :D
==Steve==

Brian Evans
Posts: 900
Joined: Sat Aug 30, 2014 8:26 am
Location: Tatamagouche, Nova Scotia

Re: Volute shape

Post by Brian Evans »

I'm more of a player than a builder, but when I play in open or first position my thumb gets directly under the nut quite a lot. Therefore my volute (the one I've done) is in the "Gibson" position. I would have a lot of issues if the peak was directly under the nut. I had to go remember which guitar had the volute, and try it, to make this determination.

John Clifford
Posts: 180
Joined: Mon Dec 18, 2017 3:08 pm

Re: Volute shape

Post by John Clifford »

Hmm - maybe Gibson knew what they were doing?? I do a little mini-volute like this, more for aesthetic reasons than for strength. I sort of balk at the idea of designing a guitar to withstand being dropped on its head. But that's probably because I'm a hobbyist, not a factory with hundreds of thousands of warranties outstanding!
Attachments
archtop volute.jpg

Brian Evans
Posts: 900
Joined: Sat Aug 30, 2014 8:26 am
Location: Tatamagouche, Nova Scotia

Re: Volute shape

Post by Brian Evans »

I found this interesting enough that I found the three guitars that i have with volutes, looked at where they are, and played them. One previously mentioned has the peak of the volute around 3/8" above the face of the nut. Very comfortable, and my thumb just rests on it's slope when I play an open C chord (I have fat fingers and big hands, and I need to really lower my wrist and get down behind the neck so the G-C-E notes are not muffled). Obviously I carved it to suit my big clumsy hands, I guess! My Paul Beard Special Goldtone dobro has a volute as suggested here, peak directly behind the nut, and it definitely interferes with my thumb in that chord. Odd that I never noticed it before but I rarely play open "cowboy chords" for that very reason - my fingers don't fit. Finally a Fender style neck on a Telecaster style guitar (a Godin TC). The very design of the Fender neck, sawn out of a slab of maple, has the back of the headstock on the same place as the heel that bolts into the body pocket, and the neck carve puts a semi-volute around 1/4" past the face of the nut. So three more place-points for the study... :)

User avatar
Steve Sawyer
Posts: 938
Joined: Wed Jan 02, 2013 2:20 pm
Location: Detroit, Michigan

Re: Volute shape

Post by Steve Sawyer »

Brian Evans wrote:So three more place-points for the study... :)
Interesting. Thanks, Brian. I have very small hands and short fingers (chording has always been my weakness), so your observations confirm that placement of the volute on this build is probably going to work for me.
==Steve==

Post Reply