stainless steel as a material for a music box comb?

Post Reply
Robert Haines
Posts: 8
Joined: Thu Jan 24, 2013 4:42 pm

stainless steel as a material for a music box comb?

Post by Robert Haines »

I'm starting on a project for making a music box that will be permanently mounted out-of-doors here in the San Francisco Bay Area, about a mile from the ocean (and consequently subjected to the corrosive atmospheric conditions that we get). I was thinking of machining the comb (or "harp", if you prefer) out of stainless steel, since it will resist rusting far better than the typical carbon steel used for music boxes.

I've been unable to find any examples of stainless being used for this purpose. From that, I could infer that it's unsuitable for making musical tones, or that there's simply no necessity for using it (since most music boxes live inside of climate-controlled rooms), or that it would sound different from a carbon steel comb of the same size (thus preventing them from working with existing cylinders), or a host of other possible explanations.

Setting aside those questions, can anyone tell me if they've heard a struck or plucked instrument that used stainless tines? -or know any reasons why it should (or shouldn't) work OK for that purpose?

FWIW, I won't be using a standard cylinder, so that part of the thing won't be a factor.

Thanks in advance!

Chris Reed
Posts: 156
Joined: Thu Feb 02, 2012 6:26 pm

Re: stainless steel as a material for a music box comb?

Post by Chris Reed »

I suspect your only course is to find a piece of stainless steel about the size of one tooth and twang it, to hear how it sounds.

If it's not musical, would bronze be worth a try? Statues survive outside, though I'm sure they're not the same bronze as sheet material.

Hope you find something, as an outdoor music box thingy sounds rather splendid!

David King
Posts: 2665
Joined: Sat Jan 07, 2012 10:01 pm
Location: Portland, OR
Contact:

Re: stainless steel as a material for a music box comb?

Post by David King »

You may also want to try titanium or aluminum, specifically Ti 6Al-4V and Al-7075 alloys.
A high carbon stainless as used in knife making would be a logical start and may be cheaper too. I'd start with 420 stainless as it's easily heat treatable.

John Morton
Posts: 5
Joined: Tue May 02, 2017 11:19 am

Re: stainless steel as a material for a music box comb?

Post by John Morton »

I agree that some empirical tests are a good way to go. I have made chimes from 1/4" aluminum plate (6061 T6) and the notes were spectacular and pure. I think the corrosion might be so slow that it wouldn't matter, except for appearance. (7075 has poor corrosion resistance, I believe.)

Ken Grunke
Posts: 1
Joined: Wed Apr 05, 2017 12:50 am

Re: stainless steel as a material for a music box comb?

Post by Ken Grunke »

I used kitchen utensils for the tines of a kalimba I made. Specifically, cake spatulas, which are between .030 and .040" thick. They are hard and stiff, and sound fairly good.
I'm also in the process of forging a one-piece jaw harp, aka jew's harp, from a butter knife.
These go for pennies at thrift shops.

User avatar
Jim McConkey
Posts: 914
Joined: Thu Jan 05, 2012 4:00 pm
Location: Way north of Baltimore, MD

Re: stainless steel as a material for a music box comb?

Post by Jim McConkey »

There is another ongoing discussion on Kalimbas here, and the original video that spurred the project used steel electrician's fishing tape for the tines. It is probably stainless, and available at every DIY store. Also look for rakes with metal tines. they are usually about the right size, and often stainless.
MIMForum Staff - Way North of Baltimore

User avatar
Andrew Porter
Posts: 98
Joined: Sun Jan 08, 2012 8:49 am
Location: The Banks of Sleepy Creek, NC, USA

Re: stainless steel as a material for a music box comb?

Post by Andrew Porter »

Google "Stainless Steel Springs".
World's Second Finest Maker of Expensive Sawdust

Post Reply