Headstock finish repair

If you have a string instrument of any kind that needs fixing, a mistake you made in building a new instrument that you need to "disappear," or a question about the ethics of altering an older instrument, ask here. Please note that it will be much easier for us to help you decide on the best repair method if you post some pictures of the problem.
Post Reply
Chris Vallillo
Posts: 111
Joined: Thu Feb 02, 2012 12:52 pm
Location: Illinois

Headstock finish repair

Post by Chris Vallillo »

I recently was asked to repair a damaged Fender acoustic (T-BUCKET™ 300CE) that had taken a fall and had the headstock broken off. It was a clean break and with the help of some "Friendly Plastic" and hot hide glue, went together quite nicely. There is quite a bit of damage to the finish on the faceplate of the headstock and a bit on the back of the neck at the break point and I'm pondering the best way to deal with this.

I have Stu Mac slow setting black epoxy but I have also recently heard that they make a black super glue as well. Would any of you with more experience in this give me your thoughts?

My current thinking is to use the epoxy for the headstock fill since it's a large, flat area, and somewhat deep but I'm not sure if it's the best thing for the smaller crack like on the back.

As always, your thoughts and opinions are greatly appreciated!
Attachments
IMG_4212.JPG
IMG_4210.JPG

Gordon Bellerose
Posts: 1178
Joined: Wed May 30, 2012 11:47 pm
Location: Edmonton AB. Canada

Re: Headstock finish repair

Post by Gordon Bellerose »

I've used the black superglue for small finish repairs. It would work for the back of the neck.
I think you're probably on the right track for the front. The only thing I worry about is color matching. Always tricky with black.
I need your help. I can't possibly make all the mistakes myself!

Barry Daniels
Posts: 2432
Joined: Thu Jan 05, 2012 10:58 am
Location: The Woodlands, Texas

Re: Headstock finish repair

Post by Barry Daniels »

Is that ebony veneer on the front?
MIMF Staff

Chris Vallillo
Posts: 111
Joined: Thu Feb 02, 2012 12:52 pm
Location: Illinois

Re: Headstock finish repair

Post by Chris Vallillo »

No. There is a thin white wood veneer over the mahogany and the top is a heavy layer of black finish. I'd assume it's some sort of catalyzed finish as this is a relatively new guitar still in production and is made in China. The "inlay" isn't really inlaid, more like decal. I'll need to mask that somehow in order to keep it from being damaged further.
Attachments
IMG_4215.JPG

Greg Steil
Posts: 158
Joined: Sat Jan 07, 2012 7:54 pm

Re: Headstock finish repair

Post by Greg Steil »

Chris, I used Epoxy with Ebony dust and CA with Ebony dust for that Gibson headstock wreck, but I also had the luxury of being able to overspray with Black Lacquer. Just do thin layers and give it plenty of time to harden.

Barry Daniels
Posts: 2432
Joined: Thu Jan 05, 2012 10:58 am
Location: The Woodlands, Texas

Re: Headstock finish repair

Post by Barry Daniels »

First off, if the inlay is simply a decal then it is not worth trying to save it because it is too close to the damage to do any effective blending. There are two issues: filling and finishing. Fill would best be done with something like Water Putty or Bondo. Sand level then finish with black opaque lacquer.

The epoxy or superglue approach would fill the depression, but you would never get a glossy finish unless it was topped with lacquer.
MIMF Staff

Barry Daniels
Posts: 2432
Joined: Thu Jan 05, 2012 10:58 am
Location: The Woodlands, Texas

Re: Headstock finish repair

Post by Barry Daniels »

I forgot that the existing finish might not be lacquer. So the first thing you should do would be to run some tests to see what the finish is. Don't just assume that it is cat poly.
MIMF Staff

Greg Steil
Posts: 158
Joined: Sat Jan 07, 2012 7:54 pm

Re: Headstock finish repair

Post by Greg Steil »

Consider staining the exposed wood first?

Chris Vallillo
Posts: 111
Joined: Thu Feb 02, 2012 12:52 pm
Location: Illinois

Re: Headstock finish repair

Post by Chris Vallillo »

OK, here's what I ended up doing. Bear in mind that this was an inexpensive guitar (299 list) and I needed to keep the cost of the repair low.

As suggested by a couple folks, I used black epoxy to fill the missing material on the faceplate. This damage was fairly deep, perhaps 1/32 or more, and needed to be filled. I used black superglue for the back of the neck crack. The super glue worked OK, but didn't set correctly even with an accelerator and tended to run which meant more scraping and sanding than I had hoped. The finish on the neck was much thinner than the faceplate and it wore through easily down to white wood. The epoxy did fill well, but was not a good match color-wise (the super glue was). I tried to color it with a a black Stu mac lacquer pen (basically a magic marker type device that has nitro cellulose lacquer in it), but when I tried to french polish over it, it dissolved.

Ultimately, what did work was coloring in the areas with black permanent marker, then french polishing over the color. It proved to be a surprisingly good match and didn't run or dissolve when I french polished over it. Multiple coats of french polish w/ 800 grit sanding between coats over the face and neck smoothed everything out nicely and made for a nice looking finish.

It's not the best work I've ever done, but turned out surprisingly well and the client was delighted.
Attachments
IMG_4227.JPG
IMG_4228.JPG

Clay Schaeffer
Posts: 1362
Joined: Fri Jan 06, 2012 12:04 pm

Re: Headstock finish repair

Post by Clay Schaeffer »

Good looking repair, Chris.
Something I've used to color epoxies, superglues, bondo, and other "putties", are pigment powders. They dissolve in most media as well as most finishing materials, and by mixing the various pigments matching the existing colors can be achieved. Very handy to have when doing finish repairs.

Greg Martin
Posts: 307
Joined: Thu Feb 23, 2012 7:18 pm

Re: Headstock finish repair

Post by Greg Martin »

Certainly a good enough repair for a 299.00 china guitar. now youve learned something you didnt know before.knowledge is always valuble.

Post Reply