Freeze Drying

Ask your wood and other materials questions here. Please DO NOT post pictures and ask us to identify your wood, we have found that accurate ID is nearly impossible, and such discussions will be deleted. Thanks.
Post Reply
User avatar
Barry Guest
Posts: 115
Joined: Sat Jan 07, 2012 10:40 pm
Location: Sydney, Australia

Freeze Drying

Post by Barry Guest »

I searched the forum to see if this topic had been mentioned previously, but didn't find a single mention. My question is: has anyone tried drying timber by freezing? Seems that you freeze a piece in a plastic bag for three days, then remove the crystalizations that form, freeze it again repeating the process until forced removal of the moisture content is reduced to the local atmospheric moisture content.

Any comments? Knowledge? Pros and cons?
Alumnus of Wood and Strings
Chuck Tweedy
Posts: 1182
Joined: Fri Jan 06, 2012 6:25 pm
Location: San Diego, CA

Re: Freeze Drying

Post by Chuck Tweedy »

Interesting idea.
I don't know how much ice you would get inside the bag. I would think the water would pretty much just stay frozen in the wood.

True freeze drying (or lyophilisation), uses vacuum to remove the water directly by sublimation (ice -> gas). So you could put the wood in a vacuum bag while frozen.
Seems like a lot of work :-)
Likes to drink Rosewood Juice
David King
Posts: 2690
Joined: Sat Jan 07, 2012 10:01 pm
Location: Portland, OR
Contact:

Re: Freeze Drying

Post by David King »

Why the plastic bag? Seems like that would prevent normal sublimation from taking place. A modern frost free freezer stays pretty dry. I might be worried about the wood picking up off odors. I'd include some baking soda in a tray.
User avatar
Mark Swanson
Posts: 1991
Joined: Thu Jan 05, 2012 11:11 am
Location: Grand Rapids, Michigan USA
Contact:

Re: Freeze Drying

Post by Mark Swanson »

I think I'd be worried about the same thing that happens to wood in a natural setting. When it is wet, and it goes through cycles of freezing/thawing, it cracks. The water in the wood expands as it freezes, something that doesn't happen when drying it normally. The freezing seems like something that could cause cracking in a thin piece of wood.
  • Mark Swanson, guitarist, MIMForum Staff
User avatar
Barry Guest
Posts: 115
Joined: Sat Jan 07, 2012 10:40 pm
Location: Sydney, Australia

Re: Freeze Drying

Post by Barry Guest »

I posted this topic after talking to a woodworker at my local market day on Sunday, selling his beautiful work from a stall.

His specialty is bowl turning. He told me he turns the bowl green, then "cures" the finished product by freezing as above until the wood is stabilized. I questioned him about splits, warps etc and he said that his success rate is above 90%. When the item comes out after freeze drying, he puts it back on the lathe to sand and finish.

He said he does it this way because he has a network of local tree loppers who supply him. By turning the item green, he sidesteps the process of natural drying or kiln drying.

Some of his work is turned down to less than a 1/4" thick, so I was amazed at this process and wanted to know more about it. Think I'll need to go back next month and have another chat.
Alumnus of Wood and Strings
Jason Rodgers
Posts: 1554
Joined: Fri Jan 06, 2012 4:05 pm
Location: Portland, OR

Re: Freeze Drying

Post by Jason Rodgers »

That's interesting, especially since bowl turners usually prefer burls and spalts that we'd consider less stable.
-Ruining perfectly good wood, one day at a time.
User avatar
Barry Daniels
Posts: 3186
Joined: Thu Jan 05, 2012 10:58 am
Location: The Woodlands, Texas

Re: Freeze Drying

Post by Barry Daniels »

Bowl turning involves different issues than guitar wood. Turners like to turn green wood because getting a large block of wood dried without cracking is difficult. Also, green wood turns more easily. Neither of those are factors for us.
MIMF Staff
David King
Posts: 2690
Joined: Sat Jan 07, 2012 10:01 pm
Location: Portland, OR
Contact:

Re: Freeze Drying

Post by David King »

Most domestic trees go down to -40º with no issues at all out in nature. The sap acts as a natural anti-freeze. As soon as the wood is cut it will usually drop excess moisture saturation until it gets to 20%. At that point a hard freeze will likely have some effect on individual cell walls but it's unlikely to cause the wood to fail completely as there's some space for the water to expand into.
Mario Proulx
Posts: 821
Joined: Fri Jan 06, 2012 12:08 pm

Re: Freeze Drying

Post by Mario Proulx »

I played around with various "tricks" early-on, and one thing I did was to soak a few raw guitar tops for a week or more, then tossed them out in my unheated garage. In January. In temps passed minus 40. Left them out there for months.... All told, the wood was neither better or worse than the sister sets that didn't get the treatment. So, it won't break, crack or split, but it also won't do anything "special" to the wood.

I have some raw spruce billets that have been in my shed for 10-12 years now, and have seen temps nearing +100°F and -54°. Nicely seasoned, but not special otherwise.
Post Reply

Return to “Wood and Materials Q&A”