Page 2 of 5

Re: Patrick DeGreve's travel guitar

Posted: Wed Apr 17, 2013 1:50 pm
by Patrick DeGreve
I am going to make rosettes for the two guitars from cut offs I saved from past projects. I save a great deal of cut-offs for pegheads, and rosettes etc. These pieces are spruce, mahogany and wenge.

Re: Patrick DeGreve's travel guitar

Posted: Wed Apr 17, 2013 2:04 pm
by Patrick DeGreve
I glued the cut-offs onto a piece of plywood and drilled a hole for the stewmac precision dremel tool. I then set up both soundboards and the plywood with the scrap pieces on my work table side-by-side. As I route the rings for the purfing, I routed the scrap without changing the settings so I will have good fitting pieces to fill the rosette with.

Re: Patrick DeGreve's travel guitar

Posted: Wed Apr 17, 2013 2:06 pm
by Patrick DeGreve
Here is a shot of the rings routed for the purfing.

Re: Patrick DeGreve's travel guitar

Posted: Wed Apr 17, 2013 2:08 pm
by Patrick DeGreve
I then glued in bwb purfing into the recess, and scraped and sanded them flush.

Re: Patrick DeGreve's travel guitar

Posted: Wed Apr 17, 2013 2:14 pm
by Patrick DeGreve
I next set up the router to route a recess between the two center rings for the pieces of scrap to fill. I removed the inside and outside waste from the routed scrap leaving only the rings.

Re: Patrick DeGreve's travel guitar

Posted: Wed Apr 17, 2013 2:18 pm
by Patrick DeGreve
Next I cut the rings into segments being carfull to keep the cuts going through the pin hole so all the pieces will join well.

Re: Patrick DeGreve's travel guitar

Posted: Wed Apr 17, 2013 2:21 pm
by Patrick DeGreve
I then glued the pieces in the recess changing the colors to make my paterns. I then scraped and sanded the rosettes flush.

Re: Patrick DeGreve's travel guitar

Posted: Wed Apr 17, 2013 2:22 pm
by Patrick DeGreve
Here is a shot of the two soundboard rosettes.

Re: Patrick DeGreve's travel guitar

Posted: Wed Apr 17, 2013 2:24 pm
by Patrick DeGreve
Here is a shot of the two soundbaords after I cut out the sound holes.

Re: Patrick DeGreve's travel guitar

Posted: Wed Apr 17, 2013 4:21 pm
by Jason Rodgers
I like your rosette process. They look cool, too!

Re: Patrick DeGreve's travel guitar

Posted: Wed Apr 17, 2013 5:11 pm
by Warren May
I like the process for your rosettes, too. The side assemblies look good. A little closer shot of your finished rosettes would be nice to see.

Re: Patrick DeGreve's travel guitar

Posted: Tue Apr 23, 2013 5:47 pm
by Patrick DeGreve
Hi Warren, Here is another shot of the rosette. I'm not sure it's any better, but if you click on the pictures they enlarge, so you can see them better.

Re: Patrick DeGreve's travel guitar

Posted: Tue Apr 23, 2013 5:57 pm
by Patrick DeGreve
I cut the braces from the best pieces of pine I had. I pre-shaped them to the 15 foot radius. They look a little large to me for the small size of guitar, I might have to scallop them after they are dry, we will see how the soundboard taps. They are only 1/4" thick, but pretty tall (5/8"). I chose a simple X brace and one tone bar per side for the steel string guitar, and a fan bracing patern for the nylon string one. The fans are 3/16th" X 1/4" tall.

Re: Patrick DeGreve's travel guitar

Posted: Tue Apr 23, 2013 5:59 pm
by Patrick DeGreve
Here is the nylon string bracing.

Re: Patrick DeGreve's travel guitar

Posted: Wed Apr 24, 2013 6:30 pm
by Warren May
I like it!

Re: Patrick DeGreve's travel guitar

Posted: Wed Apr 24, 2013 8:00 pm
by Bryan Bear
I like it, nice and clean. It's hard to tell scale on the pictures with the small body, but the ss braces look tall to me.

Re: Patrick DeGreve's travel guitar

Posted: Fri Apr 26, 2013 3:35 pm
by Greg Robinson
Looking good Patrick, very industrious. My project seems like a bit of a cop-out by comparison!

Re: Patrick DeGreve's travel guitar

Posted: Fri May 03, 2013 1:21 pm
by Patrick DeGreve
Bryan, they are small guitars, and I think the braces were a bit too much. I scaloped the braces (on the steel string) and tapered them quite a bit. The pine soundboard sounds good when tapped. I don't want to take the braces down too much because of the pine not being as strong as the spruce I have used in the past. Here is a picture of the braces after I re-worked them.

Re: Patrick DeGreve's travel guitar

Posted: Fri May 03, 2013 1:23 pm
by Patrick DeGreve
Here I glued the soundboard to the sides using the go-bar press. I did the same thing with the nylon version.

Re: Patrick DeGreve's travel guitar

Posted: Fri May 03, 2013 1:26 pm
by Patrick DeGreve
I trimed the soundboards with a flush trim bit on my router. Here is a shot of the two travel guitars from the front.