Planning a workbench, any tips?

Questions about tools and jigs you want to buy/build/modify.
Post Reply
Matthew Lau
Posts: 511
Joined: Sat Feb 18, 2012 2:03 am

Planning a workbench, any tips?

Post by Matthew Lau »

Hey everyone,

I finally got a used jointer! I'm planning on finally making a decent workbench.
I'm planning to make a 72"x 18"x34" Roubo with hard rock maple.

From an instrument maker's standpoint, is there anything that I should be aware of?

Currently, I plan to just have a leg vise, and use auxillary vises (Lee Valley holdfasts, Parrot vise, etc).

-Matt

User avatar
Bob Gramann
Posts: 965
Joined: Fri Jan 06, 2012 11:08 am
Location: Fredericksburg, VA
Contact:

Re: Planning a workbench, any tips?

Post by Bob Gramann »

Make sure it’s really the right height for you. I work standing up and 38” is the right height for me (I used to be 6’ 2” before shrinking set in with age). The wrong height hurts your arms and your back.

User avatar
Bryan Bear
Posts: 1249
Joined: Fri Jan 06, 2012 1:05 pm
Location: St. Louis, MO

Re: Planning a workbench, any tips?

Post by Bryan Bear »

What Bob said, with emphasis on right height FOR YOU. I’m shorter than Bob (5’ 11” or 5’ 10” depending on how straight I can stand) but have chronic back issues. His bench would be a bit too low for me but I can happily work at mine at 40”.
PMoMC

Take care of your feet and your feet will take care of you.

Matthew Lau
Posts: 511
Joined: Sat Feb 18, 2012 2:03 am

Re: Planning a workbench, any tips?

Post by Matthew Lau »

Thanks for the feedback!

I've been working off a Blum Benchhorse for a few years now, and find it about perfect for me. It's just about waist height.

User avatar
Bryan Bear
Posts: 1249
Joined: Fri Jan 06, 2012 1:05 pm
Location: St. Louis, MO

Re: Planning a workbench, any tips?

Post by Bryan Bear »

I would guess you have an acute understanding of how high you like your work to be so that you can do it for long periods of time. You have been raising and lowering the dental chair to custom heights so you are in a better position to make the call than most of us are for ourselves. I thought long and hard to figure mine out. I remember standing at every table and counter height I could come by to try and decide.
PMoMC

Take care of your feet and your feet will take care of you.

Ed Gerber
Posts: 9
Joined: Wed Feb 06, 2013 1:34 pm

Re: Planning a workbench, any tips?

Post by Ed Gerber »

Bench height is also dependent on the type of job you are doing; if you are using a hand plane with material in a vise a lower height would be better than the height that works for close up, intricate work. I plan to make an auxiliary bench someday that will clamp onto my bench and which raises the work table by about six inches. I also plan to make the auxiliary table with a Moxon type vise with plenty of holes for bench dogs, hold downs etc. When using a hand saw an even lower surface is better, so it really depends on what jobs you do and the tools you are using. I’m 6 feet tall and most of my benches sit at around 36 to 37”.

Another thing I like to do is use the edge of my bench as a platform for glue ups, such as binding and other long items, so having a good overhang helps. Clamping, places to attach jigs and fixtures and places to store often used tools are other considerations.

Ed

Clay Schaeffer
Posts: 1488
Joined: Fri Jan 06, 2012 12:04 pm

Re: Planning a workbench, any tips?

Post by Clay Schaeffer »

If you make an "auxiliary bench" make it large enough to stand on. You can set it on the bench to raise the work, or you can put it on the floor and stand on it to "lower" the work.

Post Reply