LMI wood

Working Osage Orange

Ask your wood and other materials questions here. Please DO NOT post pictures and ask us to identify your wood, we have found that accurate ID is nearly impossible, and such discussions will be deleted. Thanks.

Working Osage Orange

Postby Matthew Lau » Thu Feb 18, 2016 3:13 pm

In a moment of weakness (after long hours going over notes and admin work at the office), I finally broke down and bought Osage Orange.

Any tips on working with the stuff?

I was thinking of making a grammercy bow saw (or two, or three, or four) and using the rest of the stock for acoustic guitar bridge blanks. If the bow saws turn out great, I may send one to be auctioned here for MIMF.

1. I have a split billet from a freshly harvested tree from January 2016.
2. The stuff seems very, very hard. It feels at least as hard as good macassar rosewood and much tougher than the desert ironwood. Would you recommend machining it instead of using chisels and planes?
3. The stuff is very yellow. Do you guys dye it when you make stuff with it, or should I chuck it to the back of my car and let the UV brown it a bit?
4. Long term stability in an instrument?
5. Should I cut the blanks in quartersawn or rift sawn?

Thanks in advance!


ps. Please let me know if you have design ideas for the grammercy bow saws that I'll be making.
I'm thinking:
1. All Osage
2. Osage stringers, african blackwood handle and knob
3. Osage stringers, flamed maple handle and knob.

Finish may be an oil varnish or french polish (or maybe just beeswax)--would love tips.
Matthew Lau
Posts: 466
Joined: Sat Feb 18, 2012 2:03 am

Re: Working Osage Orange

Postby Bob Gramann » Thu Feb 18, 2016 4:11 pm

I make guitars out of Osage, so I can't answer all of your questions. If you just harvested the stuff, it will be a while before you can make guitars. I would seal the ends and saw it into 2" or so planks with vertical grain. After a couple of years of drying, I would saw it into back and side sets (quartersawn), weigh each set, and store it in my 40% controlled humidity room. When the weight stopped declining, I would consider it ready to work. It would be better to cycle it to higher humidity and back to miminum weight a couple of times after it reaches minimum before using it.

I cut it with a carbide blade in the bandsaw. I use sharp tools and resharpen often. When I plane it, I use a plane with a 30 degree back bevel on the blade. You have to be cognizant of grain direction when you cut. It likes to chip out and split along grain lines. It likes to chip and split when you rout it. Sometimes that can be avoided by taking the smallest cuts possible. Sometimes, not.

Any darkening disappears when you cut or sand a new surface. There's no point in darkening it until you're done machining.

Overall, I find it difficult to work. But the sound of Osage guitars makes it worth the effort.
User avatar
Bob Gramann
Posts: 924
Joined: Fri Jan 06, 2012 11:08 am
Location: Fredericksburg, VA

Re: Working Osage Orange

Postby Alan Carruth » Thu Feb 18, 2016 7:05 pm

What Bob said: it's very hard to work with hand tools. It scrapes better than it planes, for sure. It suffers a lot of drying degrade, so get rid of the tbwo or three inches of wood nearest the center to avoid lots of checking. Once it's dry it's pretty stable, although a few moisture cycles will make it more so. I have not had much luck bringing up the color. It sure makes a great instrument, though, and, as the common name of 'bodark' (bois d'arc, bow wood) attests, it's the best stuff for bows around. One of the violin bow making classes used to use it for practice, as it makes a decent bow and costs a lot less than pernambuco.
Alan Carruth
Posts: 931
Joined: Sun Jan 15, 2012 1:11 pm

Re: Working Osage Orange

Postby Randy Roberts » Fri Feb 19, 2016 9:34 am


I've used it on one guitar, but laminated kauri over it,

On the advice of the sawyer who harvested it, and who had been working for years with it, I had him ship it while still green and resawed it right away into 1/4" thick back and side sets. When green it cuts like butter, you just need to allow for the drying shrinkage. Cut that thin it will dry quickly. Once dry it is definitely a hard, hard wood. If your wood was harvested last month, I would wrap it in saran wrap, or seal it in a plastic bag, and then cut it to oversized final dimensions for what you plan to use it for. Then dry it. This will make the sawing ever so much easier, the flaw being you have to have an idea of what your final use will be.

I had no problems to speak of working it, but didn't do much hand tooling. The main drawback is the neon yellow dust everywhere. Obviously it doesn't make more dust than other woods, it's just that it's so bright you really see that it gets absolutely everywhere. (Just like the wood, the dust eventually mellows to a honey brown color <g>)
Randy Roberts
Posts: 422
Joined: Sat Jan 07, 2012 9:11 pm
Location: Omaha, NE (a suburb of Iowa)

Re: Working Osage Orange

Postby Matthew Lau » Sat Feb 20, 2016 1:27 am

Thanks for the tips!

I mainly bought it to make bow saws out of--when I got it, I realized it'll make more than a few bows.
Sounds like I'll need to treat this more like a metal than a wood.

Thanks for the tips--now I probably won't try chopping a mortise out of it.
Matthew Lau
Posts: 466
Joined: Sat Feb 18, 2012 2:03 am

Re: Working Osage Orange

Postby Dale Penrose » Sat Feb 27, 2016 2:13 pm

I have used Osage for fretboards, bridges and peg head overlays. Works great, looks really nice paired up with a cherry back and side set. Highly recommend.
Dale Penrose
Posts: 41
Joined: Wed Jan 09, 2013 5:38 pm

Re: Working Osage Orange

Postby Mark Day » Thu Apr 21, 2016 10:25 pm

I have used it to make 2 bridges; one for a uke and one for an electric lute. I really like working with it and love the highlighter yellow color. I plan on making lute ribs from some of it.
User avatar
Mark Day
Posts: 62
Joined: Wed Jan 11, 2012 8:10 pm

Re: Working Osage Orange

Postby Matthew Lau » Tue May 10, 2016 9:57 pm

Lute ribs? I suspect that they'll benefit from some time in a tanning booth.

Mine are a fluorescent yellow color!
Matthew Lau
Posts: 466
Joined: Sat Feb 18, 2012 2:03 am

Return to Wood and Materials Q&A

Who is online

Users browsing this forum: No registered users and 2 guests

Your purchase from these sites helps support the MIMForum, but only if you start at the links below!!!
Amazon music     Amazon books     Amazon tools     Rockler tools     Office Depot    

The MIMF is a member-supported forum, please consider supporting us with a donation, thanks!
 • Book store • Tool store • Links •