New project. Silvertone 672

Please put your pickup/wiring discussions in the Electronics section; and put discussions about repair issues, including fixing errors in new instruments, in the Repairs section.

New project. Silvertone 672

Postby Greg McKnight » Fri Jan 11, 2019 12:09 pm

My Granddad bought this at a yard sale several years ago and left it to his son (my uncle). It needed more TLC than he was able to give it so he sent it to me. Tuners are the obvious first priority, and I've ordered some. I'll be doing a fret leveling today and hopefully that goes well. There's no truss rod and there is a bit of difference in level between most of the fretboard and the portion directly over the body. Neck does look straight fortunately. The case is a wreck. The bridge and nut may be salvageable, but we'll see. I'll have to construct a pickguard, and these evidently came with either a black or white one with a similar shield to the headstock embossed on it. It has all the checking in the finish that you'd expect (and desire, likely). I didn't know anything about this guitar until some internet research. Silvertoneworld.com says it is a 672 which was introduced in 1950 and retired in 1953. No label inside so I guess I'll never know for sure. Should be a fun project.
Attachments
20190109_165913.jpg
20190109_165831.jpg
20190109_165903.jpg
568221192.jpg
User avatar
Greg McKnight
 
Posts: 76
Joined: Wed Dec 24, 2014 11:29 pm

Re: New project. Silvertone 672

Postby Barry Daniels » Fri Jan 11, 2019 12:16 pm

Very cool.
MIMF Staff
Barry Daniels
 
Posts: 2015
Joined: Thu Jan 05, 2012 10:58 am
Location: The Woodlands, Texas

Re: New project. Silvertone 672

Postby Greg McKnight » Fri Jan 11, 2019 1:49 pm

Barry Daniels wrote:Very cool.


Well, yes and no :lol: . Upon closer inspection, there has been a neck reset which didn't go so well. The fretboard extension is laying on the top, there's that gap at the joint, and the glue they used has dripped quite a bit inside the guitar, making a real mess. Won't be able to clean it up either, unfortunately. When I saw that the bridge had been adjusted to it's lowest position, I was concerned and now I know why that was done. The reset didn't solve any problem as far as I can tell, at least not the original problem I would guess. The glue almost looks like Elmer's school glue. It's dried hard and is milky white. Hopefully it won't be too hard to remove the neck. At least it's not epoxy!

I have done one neck reset. Oddly enough, also from a guitar from the same uncle--a Martin from the 40s if I remember correctly. It went well enough so I'm not too intimidated. Hope that glue is easy to dissolve/melt though.

I measured the scale length to be 25.875". Mind you, I used a tape measure, which might not be the most accurate method. That seems rather long but I'm far from an expert.

Well, I'll have to dig out the steam rig before I can do anything. Shame though, I wanted to get started on it.
User avatar
Greg McKnight
 
Posts: 76
Joined: Wed Dec 24, 2014 11:29 pm

Re: New project. Silvertone 672

Postby Barry Daniels » Fri Jan 11, 2019 3:45 pm

What would be your goal(s) of doing another reset?
MIMF Staff
Barry Daniels
 
Posts: 2015
Joined: Thu Jan 05, 2012 10:58 am
Location: The Woodlands, Texas

Re: New project. Silvertone 672

Postby Joshua Levin-Epstein » Sat Jan 12, 2019 4:48 am

What's wrong with the machines?
Joshua Levin-Epstein
 
Posts: 208
Joined: Sun Jan 08, 2012 7:58 am
Location: Massachusetts

Re: New project. Silvertone 672

Postby John Clifford » Sat Jan 12, 2019 4:28 pm

Interesting body shape, with the wide shoulders and tight curves at the waist. What's it sound like, or can't you tell at this point?
John Clifford
 
Posts: 110
Joined: Mon Dec 18, 2017 3:08 pm

Re: New project. Silvertone 672

Postby Brian Evans » Sun Jan 13, 2019 8:41 am

There are a lot of people who put a fair bit of love into those old Silvertones, it's worth putting back together. Or passing on to someone who will.
Brian Evans
 
Posts: 727
Joined: Sat Aug 30, 2014 8:26 am
Location: Tatamagouche, Nova Scotia

Re: New project. Silvertone 672

Postby Greg McKnight » Mon Jan 14, 2019 2:34 pm

Barry Daniels wrote:What would be your goal(s) of doing another reset?


I would hope to get it right this time around. Closing up the gaps at the bottom of the neck heel and under the fretboard extension would certainly make it look better, and there isn't a whole lot of room for a bridge as it is now. The top pic is a straight edge running on the fretboard and measuring at the bridge position.
Attachments
20190114_131901.jpg
20190109_165933.jpg
User avatar
Greg McKnight
 
Posts: 76
Joined: Wed Dec 24, 2014 11:29 pm

Re: New project. Silvertone 672

Postby Greg McKnight » Mon Jan 14, 2019 2:36 pm

Joshua Levin-Epstein wrote:What's wrong with the machines?


I thought I had included that pic the first time around.
Attachments
20190109_165919 (1).jpg
User avatar
Greg McKnight
 
Posts: 76
Joined: Wed Dec 24, 2014 11:29 pm

Re: New project. Silvertone 672

Postby Barry Daniels » Tue Jan 15, 2019 11:50 am

Wow!
MIMF Staff
Barry Daniels
 
Posts: 2015
Joined: Thu Jan 05, 2012 10:58 am
Location: The Woodlands, Texas


Return to Archtop Guitars and Bass Guitars

Who is online

Users browsing this forum: No registered users and 4 guests

Your purchase from these sites helps support the MIMForum, but only if you start at the links below!!!
Amazon music     Amazon books     Amazon tools     Rockler tools     Office Depot    

The MIMF is a member-supported forum, please consider supporting us with a donation, thanks!
 • Book store • Tool store • Links •