$100 Local Materials Challenge, California redwood, walnut OM (Completed 5/19/12)

Here is where you put your entries.
User avatar
Patrick DeGreve
Posts: 308
Joined: Mon Jan 09, 2012 2:19 pm

$100 Local Materials Challenge, California redwood, walnut OM (Completed 5/19/12)

Post by Patrick DeGreve »

I put my challenge listing in the wrong place, so I am moving it here where it belongs. I plan to make two instruments for this challenge. This one is going to be an OM with a California redwood soundboard, and walnut back and sides. The neck will be a laminate of walnut, and oak. I am using walnut for the fretboard, and bridge as well. Here is a shot of some of my materials.
Attachments
Materials.jpg
User avatar
Patrick DeGreve
Posts: 308
Joined: Mon Jan 09, 2012 2:19 pm

Re: $100 Local Materials Challenge, California redwood, walnut OM

Post by Patrick DeGreve »

I started with the bridge. I read with interest the thread on using walnut for a bridge in the flat top guitar section of this forum and made my bridge deeper for a better footprint. I think this is a good idea because of the redwood soundboard as well. I think I will dowel the bridge as well. Here I set up a stop to route the saddle slot.
Attachments
making-bridge.jpg
User avatar
Patrick DeGreve
Posts: 308
Joined: Mon Jan 09, 2012 2:19 pm

Re: $100 Local Materials Challenge, California redwood, walnut OM

Post by Patrick DeGreve »

Here is a shot of the bridge after drilling the pin holes and shaping the bridge.
Attachments
walnut-bridge.jpg
User avatar
Patrick DeGreve
Posts: 308
Joined: Mon Jan 09, 2012 2:19 pm

Re: $100 Local Materials Challenge, California redwood, walnut OM

Post by Patrick DeGreve »

I had a chance to get back to the challenge instruments yesterday. I re-sawed the walnut for the back and sides. I cut the sides about 1/8", and then planed them to .090". I cut the backs a little thicker, so I could plane them down to 1/8".
Attachments
resaw-back.jpg
User avatar
Patrick DeGreve
Posts: 308
Joined: Mon Jan 09, 2012 2:19 pm

Re: $100 Local Materials Challenge, California redwood, walnut OM

Post by Patrick DeGreve »

After trimming the sides to their profile shape, I bent them in my fox style bender.
Attachments
bending-sides.jpg
User avatar
Patrick DeGreve
Posts: 308
Joined: Mon Jan 09, 2012 2:19 pm

Re: $100 Local Materials Challenge, California redwood, walnut OM

Post by Patrick DeGreve »

Next I made the neck and heel blocks. I made these out of some mahogany, (not a local wood),but I was not sure if walnut was suitable for the neck block. I had some mahogany that I have used for neck blocks before, and was afraid that walnut might be more prone to spliting. Here I am gluing them in place.
Attachments
neckand-heel.jpg
User avatar
Patrick DeGreve
Posts: 308
Joined: Mon Jan 09, 2012 2:19 pm

Re: $100 Local Materials Challenge, California redwood, walnut OM

Post by Patrick DeGreve »

I made some kerfing from a piece of hard pine I pulled out of the trash at work. I work in TV a production shop in Hollywood, and the carpenters throw out pine cut offs all the time. I ripped it down to 1/4" X 3/4 ", routed one side with a round over bit, and cut the kerfing with a stop on my band saw.
Attachments
kerfing.jpg
User avatar
Patrick DeGreve
Posts: 308
Joined: Mon Jan 09, 2012 2:19 pm

Re: $100 Local Materials Challenge, California redwood, walnut OM

Post by Patrick DeGreve »

Here I glued on the kerfing. I bought some small spring clamps for this purpose, clothes pins alone just don't have strength.
Attachments
clamping-kerfing.jpg
User avatar
Patrick DeGreve
Posts: 308
Joined: Mon Jan 09, 2012 2:19 pm

Re: $100 Local Materials Challenge, California redwood, walnut OM

Post by Patrick DeGreve »

Here I am thicknessing the soundboard. I double faced taped the soundboard to a plywood sled, ran it through the thickness planner. I thicknessed the soundboard to .130". This is just a bit more than spruce would be, because of the redwood.
Attachments
thicknessingsoundboard..jpg
User avatar
Patrick DeGreve
Posts: 308
Joined: Mon Jan 09, 2012 2:19 pm

Re: $100 Local Materials Challenge, California redwood, walnut OM

Post by Patrick DeGreve »

Gluing the soundboard pieces together.
Attachments
gluing-soundboar.jpg
User avatar
Patrick DeGreve
Posts: 308
Joined: Mon Jan 09, 2012 2:19 pm

Re: $100 Local Materials Challenge, California redwood, walnut OM

Post by Patrick DeGreve »

Using Stew-mac's precision routing base, I routed four rings for the purfling strips. I also routed the same rings in pine, walnut, and redwood. I will use the ridges between the rings for inlay material.
Attachments
start-rosette.jpg
User avatar
Patrick DeGreve
Posts: 308
Joined: Mon Jan 09, 2012 2:19 pm

Re: $100 Local Materials Challenge, California redwood, walnut OM

Post by Patrick DeGreve »

Here is the finished rosette.
Attachments
rosette.jpg
User avatar
Patrick DeGreve
Posts: 308
Joined: Mon Jan 09, 2012 2:19 pm

Re: $100 Local Materials Challenge, California redwood, walnut OM

Post by Patrick DeGreve »

I cut out the soundboard, leaving about 1/2" outside the line.
Attachments
soundboard.jpg
User avatar
Patrick DeGreve
Posts: 308
Joined: Mon Jan 09, 2012 2:19 pm

Re: $100 Local Materials Challenge, California redwood, walnut OM

Post by Patrick DeGreve »

After finishing the rosette, I glued up the back the same way as the soundboard. Here is a shot of the back after sanding.
Attachments
back.jpg
User avatar
Eddie McRae
Posts: 153
Joined: Thu Feb 23, 2012 10:07 am
Location: Woodbury, GA USA
Contact:

Re: $100 Local Materials Challenge, California redwood, walnut OM

Post by Eddie McRae »

Very nice! I'm crazy about black walnut and use it quite a bit. Nice to see someone else using it too! Nice job on the rosette also. Looking good!
Chuck Tweedy
Posts: 1182
Joined: Fri Jan 06, 2012 6:25 pm
Location: San Diego, CA

Re: $100 Local Materials Challenge, California redwood, walnut OM

Post by Chuck Tweedy »

That back is outstanding!! Can't wait to see the whole thing.
Rosette is cool as well. :-)
Likes to drink Rosewood Juice
Thomas Dooher
Posts: 61
Joined: Fri Jan 13, 2012 7:18 pm

Re: $100 Local Materials Challenge, California redwood, walnut OM

Post by Thomas Dooher »

Yeah, another one that make me ill...wish I had as much talent! :mrgreen: with envy...
User avatar
Patrick DeGreve
Posts: 308
Joined: Mon Jan 09, 2012 2:19 pm

Re: $100 Local Materials Challenge, California redwood, walnut OM

Post by Patrick DeGreve »

Back to work on my projects, I cut the walnut and oak into strips, which I glued up into a neckblock.
Attachments
gluing-neck.jpg
User avatar
Patrick DeGreve
Posts: 308
Joined: Mon Jan 09, 2012 2:19 pm

Re: $100 Local Materials Challenge, California redwood, walnut OM

Post by Patrick DeGreve »

Here is a shot of the neck block. The center piece is 1/2" X 1" X 32", the two oak strips are 1/4" X 1" X32", and the outer strips are 3/4" X 1" X 32".
Attachments
neck.jpg
User avatar
Patrick DeGreve
Posts: 308
Joined: Mon Jan 09, 2012 2:19 pm

Re: $100 Local Materials Challenge, California redwood, walnut OM

Post by Patrick DeGreve »

I decided to use the spruce bracing wood that I had, instead of the pine that I was going to use. I just thought that the pine was not stiff enough for the redwood soundboard. I pre-shaped the braces to a 15' radius with a plane, and scraper, and sanded them smooth. Then glued them in place on a radius disk.
Attachments
soundboardglueup.jpg
Post Reply

Return to “The Local Materials Challenge (Closed)”