softening Gorilla glue

Please put your pickup/wiring discussions in the Electronics section; and put discussions about repair issues, including fixing errors in new instruments, in the Repairs section.
Post Reply
Dave Teeter
Posts: 3
Joined: Sun Nov 23, 2014 8:03 pm

softening Gorilla glue

Post by Dave Teeter »

I recently purchased an old arch top. The neck has a definite bow which I want to remove. Upon removing the fingerboard I discovered that someone previously had done a neck reset and glued it in with Gorilla glue. I have tried steam and acetone to try to soften the glue enough to remove the neck. I have found nothing that works. Any ideas?
User avatar
Barry Daniels
Posts: 3186
Joined: Thu Jan 05, 2012 10:58 am
Location: The Woodlands, Texas

Re: softening Gorilla glue

Post by Barry Daniels »

I don't know of anything that will dissolve polyurethane glue.

Why do you need to remove the neck? What are you planning on doing to straighten the neck? Does it have a truss rod?
MIMF Staff
Dave Teeter
Posts: 3
Joined: Sun Nov 23, 2014 8:03 pm

Re: softening Gorilla glue

Post by Dave Teeter »

I want to remove the neck, plane it then install a carbon fiber tube for strength. At present it only has a thin steel bar, which definitely did not work.
User avatar
Barry Daniels
Posts: 3186
Joined: Thu Jan 05, 2012 10:58 am
Location: The Woodlands, Texas

Re: softening Gorilla glue

Post by Barry Daniels »

I install carbon fiber bars in necks without taking the neck off. Might want to check the threads here. By the way, a solid carbon bar or rod is stiffer than a hollow tube.

https://www.mimf.com//phpbb/viewtopic.php?f=8&t=5890

https://www.mimf.com//phpbb/viewtopic.php?f=8&t=5637
MIMF Staff
David King
Posts: 2690
Joined: Sat Jan 07, 2012 10:01 pm
Location: Portland, OR
Contact:

Re: softening Gorilla glue

Post by David King »

You could potentially saw the neck out with a series of razor saws and destroy either the neck or the end-block in the process.
If you were patient enough you might be able to drill a series of adjacent holes down through the glueline from above since the fingerboard is off. If that worked you could then build the tenon back up to fill the newly enlarged mortice. You can get 1/16" x 6" "aircraft drills" from any MRO or tooling distributor such as Travers Tool or https://www.mscdirect.com . Something like a 1/8" bradpoint would go a lot faster and might be easier to guide.
Brian Evans
Posts: 922
Joined: Sat Aug 30, 2014 8:26 am
Location: Tatamagouche, Nova Scotia

Re: softening Gorilla glue

Post by Brian Evans »

Presuming it's an old Kay or something non-invaluable like that, and you want to be able to play it, I might cut the neck off and make a new one, or cut it off and convert to a two bolt butt joint type neck.
User avatar
Peter Wilcox
Posts: 1317
Joined: Sun Jan 08, 2012 1:31 am
Location: Northeastern California

Re: softening Gorilla glue

Post by Peter Wilcox »

Brian Evans wrote:Presuming it's an old Kay or something non-invaluable like that, and you want to be able to play it, I might cut the neck off and make a new one, or cut it off and convert to a two bolt butt joint type neck.
Like this: http://www.frets.com/FretsPages/Luthier ... eset1.html
Maybe I can't fix it, but I can fix it so no one can fix it
Mike Spector
Posts: 14
Joined: Sun Jul 03, 2016 9:55 am

Re: softening Gorilla glue

Post by Mike Spector »

If the inlays don't mean a lot to you, I would build a simple sled to fit around the neck and take a router to the fingerboard. Once off, install the rods or whatever.
Dave Teeter
Posts: 3
Joined: Sun Nov 23, 2014 8:03 pm

Re: softening Gorilla glue

Post by Dave Teeter »

Thanks to all for your helpful replies. I'll see what happens.
Post Reply

Return to “Archtop Guitars and Bass Guitars”