In the works

Please put your pickup/wiring discussions in the Electronics section; and put discussions about repair issues, including fixing errors in new instruments, in the Repairs section.

In the works

Postby Andy Bounsall » Sun Jan 28, 2018 3:36 pm

I haven't posted anything for a while so I thought I'd share a few photos of the two acoustics that I'm currently building. One is purpleheart and curly maple with a spruce top. The other is flame birch with a chocolate brown western red cedar top. Enjoy!
Attachments
IMG_1218.JPG
IMG_1220.JPG
IMG_1219.JPG
Andy Bounsall
 
Posts: 44
Joined: Thu Feb 02, 2012 12:29 pm
Location: Ottawa, Ontario, Canada

Re: In the works

Postby John Clifford » Mon Jan 29, 2018 12:33 am

Why the open tail blocks?
John Clifford
 
Posts: 53
Joined: Mon Dec 18, 2017 3:08 pm

Re: In the works

Postby Andy Bounsall » Mon Jan 29, 2018 8:22 am

John Clifford wrote:Why the open tail blocks?

I'm trying something new (for me). Since these guys don't have traditional sound holes, there's no easy way to gain access to the inside to attach the bolt on neck, nor in the event that repairs, etc are ever needed. I made the tail blocks so that there's an access hole big enough to get a hand and forearm into. A matching piece of the side wood is attached to the cutout to form a trap door which, when completed, will blend in with the design and be almost invisible. Not shown in the photos below, but there I'll be a mechanism by which the removable trap door will be secured from the inside.
Attachments
IMG_1228.JPG
IMG_1227.JPG
IMG_1226.JPG
IMG_1225.JPG
Andy Bounsall
 
Posts: 44
Joined: Thu Feb 02, 2012 12:29 pm
Location: Ottawa, Ontario, Canada

Re: In the works

Postby Gordon Bellerose » Mon Jan 29, 2018 10:12 am

Forgive me for asking, but how will you get inside to activate the mechanism?
Or will it in some way, be integral with the strap button?
I need your help. I can't possibly make all the mistakes myself!
Gordon Bellerose
 
Posts: 1019
Joined: Wed May 30, 2012 11:47 pm
Location: Edmonton AB. Canada

Re: In the works

Postby Andy Bounsall » Mon Jan 29, 2018 10:52 am

Good guess Gordon.

There'll be a short aluminum bar that spans across the inside of the access hole. An end pin jack, attached to the bar, will poke out through a hole in the trap door. Tightening the nut on the outside of the end pin jack will pull the bar outwards and the trap door inwards, locking the whole thing in place. At least that's the plan.

Clear as mud? I'll post some pics of the contraption once I have it all put together.
Andy Bounsall
 
Posts: 44
Joined: Thu Feb 02, 2012 12:29 pm
Location: Ottawa, Ontario, Canada

Re: In the works

Postby Bryan Bear » Mon Jan 29, 2018 3:48 pm

I made an access plug that operated similarly to this. When you twisted the end pin it rotated the steel bar to verticle then pulled it all together to squeeze the plug in place. I like the dowel corners on your plug, did you do that because you drilled out the block then cut or for some other reason?
PMoMC

Take care of your feet and your feet will take care of you.
User avatar
Bryan Bear
 
Posts: 977
Joined: Fri Jan 06, 2012 1:05 pm
Location: St. Louis, MO

Re: In the works

Postby Andy Bounsall » Mon Jan 29, 2018 6:28 pm

I wanted a nice snug but not tight fit. Drilled the four corners (5/16" I think), cut between with a thin scroll saw, then glued the dowels into the drill holes. Worked out quite nicely.
Andy Bounsall
 
Posts: 44
Joined: Thu Feb 02, 2012 12:29 pm
Location: Ottawa, Ontario, Canada

Re: In the works

Postby Bob Francis » Mon Jan 29, 2018 6:50 pm

Very clever
Bob Francis
 
Posts: 375
Joined: Wed Jan 11, 2012 6:28 pm

Re: In the works

Postby Bryan Bear » Tue Jan 30, 2018 11:05 am

That makes sense. I made mine by cutting up and re-laminating the tail block. It was similar to how you would make a bandsaw box.
PMoMC

Take care of your feet and your feet will take care of you.
User avatar
Bryan Bear
 
Posts: 977
Joined: Fri Jan 06, 2012 1:05 pm
Location: St. Louis, MO

Re: In the works

Postby Clay Schaeffer » Tue Jan 30, 2018 2:33 pm

I made a tail port that was oval shaped and used a wooden "bar" to hold it in place. Just another way to do it. To fill the kerf that the coping saw blade made I moved the two cut off pieces of the sides outward before gluing them to the plywood backing - leaving a gap between them , which I later filled with an end graft. It allowed me to grain match the port to the remaining sides.

Hey Andy,
Is the F hole guitar a flat top or semi arch top? I've been thinking about making one with a strong cylindrical arching scheme (that I use for octave mandos) using a typical flat top soundboard.
Attachments
tail port.jpg
Clay Schaeffer
 
Posts: 1114
Joined: Fri Jan 06, 2012 12:04 pm

Re: In the works

Postby Andy Bounsall » Tue Jan 30, 2018 3:34 pm

Clay Schaeffer wrote:...Is the F hole guitar a flat top or semi arch top?

Clay, it's a flat top - the same 25' radius that I normally use for acoustic guitars.
Andy Bounsall
 
Posts: 44
Joined: Thu Feb 02, 2012 12:29 pm
Location: Ottawa, Ontario, Canada

Re: In the works

Postby Gordon Bellerose » Wed Jan 31, 2018 7:33 pm

Would it make sense that the aluminum bar you mention, would be as wide as the "plug" itself when turned horizontal?
And then when turned vertical it would be long enough to hold the plug in?
All of that could be controlled with a couple of small dowels placed as stops on the inside of the plug?
I need your help. I can't possibly make all the mistakes myself!
Gordon Bellerose
 
Posts: 1019
Joined: Wed May 30, 2012 11:47 pm
Location: Edmonton AB. Canada

Re: In the works

Postby Bryan Bear » Wed Jan 31, 2018 7:45 pm

Gordon Bellerose wrote:Would it make sense that the aluminum bar you mention, would be as wide as the "plug" itself when turned horizontal?
And then when turned vertical it would be long enough to hold the plug in?
All of that could be controlled with a couple of small dowels placed as stops on the inside of the plug?


That’s how mine worked, though it was a rectangle not an oval.
PMoMC

Take care of your feet and your feet will take care of you.
User avatar
Bryan Bear
 
Posts: 977
Joined: Fri Jan 06, 2012 1:05 pm
Location: St. Louis, MO

Re: In the works

Postby James Meloan » Wed Feb 07, 2018 7:35 am

I've been really curious what flattops with f-holes sound like. I've never gotten my hands on one but have seen a few pictures. Do you notice a difference between them and guitars with round soundholes located in the usual place or not so much? I've heard some things here and there about f-holes and their effect on the sound of viol instruments but I'm not sure what's legit vs speculation.
James Meloan
 
Posts: 13
Joined: Thu Jan 12, 2017 2:35 pm

Re: In the works

Postby Matthew Lau » Fri Feb 09, 2018 12:26 am

Nice!

I really look forward to going back to building
Matthew Lau
 
Posts: 399
Joined: Sat Feb 18, 2012 2:03 am

Re: In the works

Postby Brian Evans » Fri Feb 09, 2018 8:45 am

All I do is drill a 7/16" hole through the tail block and poke a long allen key wrench through. The hole is either covered up with the tail-piece, or I use it for the end-pin if a cable type tailpiece. This time I am strongly considering a single bolt into the neck block from the neck heel, dual use for a strap pin. One bolt is more than enough. I do use a tightly fitted plain tenon to stabilize the neck.
Brian Evans
 
Posts: 605
Joined: Sat Aug 30, 2014 8:26 am
Location: Tatamagouche, Nova Scotia


Return to Flat-Top Acoustic Guitars and Bass Guitars

Who is online

Users browsing this forum: No registered users and 1 guest

Your purchase from these sites helps support the MIMForum, but only if you start at the links below!!!
Amazon music     Amazon books     Amazon tools     Rockler tools     Office Depot    

The MIMF is a member-supported forum, please consider supporting us with a donation, thanks!
 • Book store • Tool store • Links •