StewMac tools            

Archtop #1 in progress

Please put your pickup/wiring discussions in the Electronics section; and put discussions about repair issues, including fixing errors in new instruments, in the Repairs section.

Archtop #1 in progress

Postby Greg McKnight » Tue Jun 23, 2015 10:03 pm

I've had a couple of things done on my first archtop build for a few months. Finally getting around to making a build thread to document it all. Top is Engleman and back and sides will be black walnut. Three piece maple neck with walnut headstock overlay planned.

Here is the shortcut setup for the top and back carves. So far I only have the top started.
Image

Getting there.
Image

And after a little time with a sharp chisel cutting down the ledges.
Image

Here is the back. Should get around to stepping it in a day or two.
Image

The center line on the walnut is not at the joining of the two halves unfortunately. Just didn't work out with the wood I had.
User avatar
Greg McKnight
 
Posts: 68
Joined: Wed Dec 24, 2014 11:29 pm

Re: Archtop #1 in progress

Postby Mike Conner » Wed Jun 24, 2015 5:57 am

Looking forward to this thread, Greg!

What are you planning for binding? Maple can look really good against the walnut.
Mike Conner
 
Posts: 117
Joined: Wed Feb 08, 2012 8:12 pm
Location: Seneca SC

Re: Archtop #1 in progress

Postby Greg McKnight » Wed Jun 24, 2015 6:46 am

To be honest I can't remember whether I bought black or white binding, it's been so long since I looked in the "goodie box" of guitar parts and supplies. I think I intended to do the opposite of what I saw in Benedetto's book, using black where he used white and vice versa. The main reason for that is that I thought I would just have a natural or honey blonde top finish and the black would be a nice contrasting color. I really wanted to use tortoise binding but couldn't find any that looked like I wanted.
User avatar
Greg McKnight
 
Posts: 68
Joined: Wed Dec 24, 2014 11:29 pm

Re: Archtop #1 in progress

Postby Mike Conner » Wed Jun 24, 2015 10:42 am

Greg, I really liked the contrast between the plain or curly maple and the dark walnut, especially the curly maple. So far I have only used wood bindings I made myself - no problem bending them and I could use regular Titebond glue.

The second walnut build I did (my Number 4) I used an ebony grain filler mixed using Elmers ProBond wood filler and distilled water. To avoid discoloring the front plate and binding I taped off the walnut, applied a light honey amber toner, then sealed with 3 coats of EnduroVar, then did the filler. It was a messy job to sand out, but it worked really well.

I guess the point is to consider whether you want the walnut grain filled or not. I like the look either way, though filling the grain with a dark filler enhanced the grain pattern and gave a flatter finished surface. I do not want to intrude into your design or intentions, just wanted to share some thoughts. I really like walnut for archtops even though the typical jazz guitar aficiaondo would expect to see maple.
Mike Conner
 
Posts: 117
Joined: Wed Feb 08, 2012 8:12 pm
Location: Seneca SC

Re: Archtop #1 in progress

Postby Greg McKnight » Wed Jun 24, 2015 5:40 pm

I've always used a black grain filler on walnut and I like the look too, Mike. Really does make it pop once the finish is on.
User avatar
Greg McKnight
 
Posts: 68
Joined: Wed Dec 24, 2014 11:29 pm

Re: Archtop #1 in progress

Postby Greg McKnight » Tue Jun 30, 2015 4:03 pm

Did a little more carving the past couple of days and it's starting to look like a guitar-shaped object. I may be further along if I could find my smaller finger plane :P . Or if I had a nice sharp gouge to get into some of the curvy parts.
Image

The neck is ready to cut the tenon on but I will have to have a practice run on something cheap first.
Image

Here are the sides. Still a bit too thick at this point, I'll have to glue or double stick tape them to a board and send it through the planer to thin them down. The end of one is starting to split but I have longer pieces than I need so it should be okay.
Image
User avatar
Greg McKnight
 
Posts: 68
Joined: Wed Dec 24, 2014 11:29 pm

Re: Archtop #1 in progress

Postby Mike Conner » Tue Jun 30, 2015 8:00 pm

Greg,
Rug tape from Walmart works great - I just use a piece at each end and live with the slight "snipe". Slip a knife between the rug tape and side and it will release cleanly.

Superglue the split now, before doing any more planing or sanding, to keep the split from running down the grain. Superglue is your friend when planing or bending!
Mike Conner
 
Posts: 117
Joined: Wed Feb 08, 2012 8:12 pm
Location: Seneca SC

Re: Archtop #1 in progress

Postby Greg McKnight » Tue Jun 30, 2015 9:23 pm

Thanks for the tips Mike. I've got some of that rug/carpet tape, and boy howdy does it hold well ;) . I'll glue the side split tomorrow.

I have to say, the carving process on the spruce is a nice, therapeutic thing to do. I'm learning about the sharpening process too, but very slowly. That just seems to be one of those things you'll probably only "get" with experience.

BTW, what is your recommendation for side thickness? I think they stand at 3/32" now; the thinnest the planer would take them.
User avatar
Greg McKnight
 
Posts: 68
Joined: Wed Dec 24, 2014 11:29 pm

Re: Archtop #1 in progress

Postby Mike Conner » Wed Jul 01, 2015 6:10 am

Yep, carving the spruce is great meditation. I really like the sound of the plane "ringing" from the plate.
OTOH, carving walnut or maple back plates is anger management therapy.

You are pretty close on your sides! I never trusted my Dewalt planer to go that low without a backing board.
3/32" is" about 0.094". I target 0.077" off the planer and that leaves a little bit for sanding or scraping.
You can be thinner at the cutaway bend, maybe 0.065" or so.

BTW, planing this way (sticking the thin side blanks to a carrier board) is the same way I prepare wood bindings. Essentially, my wood bindings are a side blank ripped down to 1/4" wide strips at the bandsaw. I gang the binding strips together on edge and clean up both edges to ensure they all end up the same width, then scrape them down to about 0.065" (for a 0.060" channel).
Mike Conner
 
Posts: 117
Joined: Wed Feb 08, 2012 8:12 pm
Location: Seneca SC

Re: Archtop #1 in progress

Postby Randolph Rhett » Wed Jul 01, 2015 11:09 am

Mike Conner wrote:Yep, carving the spruce is great meditation. I really like the sound of the plane "ringing" from the plate.
OTOH, carving walnut or maple back plates is anger management therapy.



:lol: I was just going to say something like that!
User avatar
Randolph Rhett
 
Posts: 251
Joined: Mon Aug 06, 2012 5:19 pm
Location: San Diego, CA

Re: Archtop #1 in progress

Postby Greg McKnight » Thu Jul 16, 2015 6:18 pm

After a session of practice side bending, I dove right in this morning. The top ended up fine but of course the side with the cutaway didn't make it without a split. My plan is to let the side dry out and then sand it thinner in those spots it will need to bend more sharply in. Will it be okay to glue the split before I do that, and what glue should I use?

I would love to show a pic of the completed top carve but my camera went toes up so that ain't happening. I'll borrow one soon to keep the thread going.
User avatar
Greg McKnight
 
Posts: 68
Joined: Wed Dec 24, 2014 11:29 pm

Re: Archtop #1 in progress

Postby Mike Conner » Thu Jul 16, 2015 7:32 pm

Greg,
Is the split along the grain, or is it like a delamination where part of the thickness popped or pealed up?

Either way, the couple of times that has happened (walnut, cherry) after letting the wood dry out some I used some medium thick "maximum bond" superglue in the split, then clamped it back down with wax paper to prevent adhering the scrap wood caul. I make sure to buy some fresh superglue at Walmart and/or use a new unopened tube since superglue has a shelf life.

Since moisture helps set superglue I didn't worry too much about having the wood bone dry.

Worked for me, and when back to bending the superglue held up fine.

Sanding thinner would probably help a bit too. When bending walnut, I found it reduced the chance for splitting by doing the cutaway bend in two or three sessions and sneaking up on it rather than doing it all in one bend.
Mike Conner
 
Posts: 117
Joined: Wed Feb 08, 2012 8:12 pm
Location: Seneca SC

Re: Archtop #1 in progress

Postby Greg McKnight » Thu Jul 16, 2015 9:20 pm

It split along the grain. This section, unlike the one I used for the top, has a little "figure" in it rather than straight grain. I'll used some CA glue and sand a little thinner and try again tomorrow.
User avatar
Greg McKnight
 
Posts: 68
Joined: Wed Dec 24, 2014 11:29 pm

Re: Archtop #1 in progress

Postby Michael Lewis » Fri Jul 17, 2015 3:12 am

I hate to beat a thing to death but hot hide glue will hold up better than most other glues if you can get the surfaces to mate well while drying, and hide glue shows less under finish than any other glue.

No matter what glue you make the repair with you are more likely to have a bit of difficulty with the separation than if it hadn't separated. In short, it is more difficult to bend a repaired section than to bend an undamaged section.
Michael Lewis
 
Posts: 1446
Joined: Thu Jan 12, 2012 1:22 am
Location: Northern California USA

Re: Archtop #1 in progress

Postby Greg McKnight » Sat Jul 18, 2015 1:04 pm

Fortunately, I cut the sides longer than needed, so I was able to flip it around and start from the other end. This morning I got a pot of water boiling on a hot plate nearby and kept dipping the cutaway section in there. Eventually it got pretty limber and I was able to clamp it in. Phew!

Now that I've done it, I know what would be ideal: a cutaway-shaped insert to clamp in the mold on top of it. Similar to the insert for the professional benders I've seen but just a little block. Oh well, live and learn. It's starting to come together.
User avatar
Greg McKnight
 
Posts: 68
Joined: Wed Dec 24, 2014 11:29 pm

Re: Archtop #1 in progress

Postby Patrick Hanna » Mon Jul 20, 2015 1:00 pm

Keep us posted, Greg. I loved the experience of making my walnut-backed archtop and I love the guitar. Honestly, I didn't mind planing the back to shape. I did it all with the plane and some templates--no pre-stepping. I did pre-drill the inside contour, however. Just try going diagonally across the grain in various directions until you find out how that particular section of board wants to be shaved. Do thin shavings and don't be in a hurry. I think you'll love it. Best of luck as you work forward!
Patrick
Patrick Hanna
 
Posts: 197
Joined: Sun Jan 08, 2012 10:49 am

Re: Archtop #1 in progress

Postby Dan Smith » Mon Jul 20, 2015 1:26 pm

Looks great Greg!
How thick is your hunk of Spruce?
It looks like a pretty tall arch.
Dan
Ever-body was kung fu fight-in,
Them kids was fast as light-nin.
User avatar
Dan Smith
 
Posts: 301
Joined: Mon May 18, 2015 9:33 pm
Location: Texas

Re: Archtop #1 in progress

Postby Greg McKnight » Wed Jul 22, 2015 9:18 am

Dan Smith wrote:Looks great Greg!
How thick is your hunk of Spruce?
It looks like a pretty tall arch.
Dan


It was just under an inch Dan (about .97 I think). I used the Benedetto arch templates and it lined up well. Must be an optical illusion :P .

I've since gotten the sides bent and the tail and neck blocks glued in. Still in search of an option for pics however.
User avatar
Greg McKnight
 
Posts: 68
Joined: Wed Dec 24, 2014 11:29 pm

Re: Archtop #1 in progress

Postby Greg McKnight » Thu Jul 23, 2015 9:11 pm

Here is the bender in case anyone was interested. Just your typical piece of pipe with a charcoal starter in it.
Image

And here I've almost completed one side of the purfling and so forth after gluing in the neck and tail blocks.
Image
User avatar
Greg McKnight
 
Posts: 68
Joined: Wed Dec 24, 2014 11:29 pm

Re: Archtop #1 in progress

Postby Greg McKnight » Thu Jul 23, 2015 10:07 pm

And yes, I do realize that it's kerfed linings rather than purfling. Just a slip of the mind.
User avatar
Greg McKnight
 
Posts: 68
Joined: Wed Dec 24, 2014 11:29 pm

Next

Return to Archtop Guitars and Bass Guitars

Who is online

Users browsing this forum: No registered users and 0 guests

Your purchase from these sites helps support the MIMForum, but only if you start at the links below!!!
Amazon music     Amazon books     Amazon tools     Rockler tools     Office Depot    

The MIMF is a member-supported forum, please consider supporting us with a donation, thanks!
 • Book store • Tool store • Links •