Patrick DeGreve's travel guitar

Opens April 1st!

Re: Patrick DeGreve's travel guitar

Postby Patrick DeGreve » Fri May 03, 2013 1:31 pm

Here is a shot of the two travel guitars from the back, showing the different bracing patterns (steel srtring vs nylon string).
Attachments
2back.jpg
User avatar
Patrick DeGreve
 
Posts: 307
Joined: Mon Jan 09, 2012 2:19 pm

Re: Patrick DeGreve's travel guitar

Postby Patrick DeGreve » Fri May 03, 2013 1:36 pm

Just to give an idea of the size of the travel guitars, here is a shot of the travel guitars with the uke I am building for my other project.
Attachments
2trio.jpg
User avatar
Patrick DeGreve
 
Posts: 307
Joined: Mon Jan 09, 2012 2:19 pm

Re: Patrick DeGreve's travel guitar

Postby Patrick DeGreve » Fri May 03, 2013 1:49 pm

Now to start the neck. I like a blocked up neck. I like the look, and it adds strength. I took a piece of the oak flooring that was flat sawn and planed off the finish. Then I cut it into two lengths 1" X 28". When I glue them up the grain will run vertical, making them the same as a quarter sawn blank. I also cut a center strip from some maple I had 1" X 3/8" X 28", and two strips from some walnut at 1/4" X 1" X 28". These will become the neck blank.
Attachments
2neckblank.jpg
User avatar
Patrick DeGreve
 
Posts: 307
Joined: Mon Jan 09, 2012 2:19 pm

Re: Patrick DeGreve's travel guitar

Postby Patrick DeGreve » Fri May 03, 2013 1:50 pm

Before I glue them together I ran them all through the planer.
Attachments
2planing.jpg
User avatar
Patrick DeGreve
 
Posts: 307
Joined: Mon Jan 09, 2012 2:19 pm

Re: Patrick DeGreve's travel guitar

Postby Patrick DeGreve » Fri May 03, 2013 1:51 pm

Then I glued them up to make a neck blank.
Attachments
2neckglue.jpg
User avatar
Patrick DeGreve
 
Posts: 307
Joined: Mon Jan 09, 2012 2:19 pm

Re: Patrick DeGreve's travel guitar

Postby Hans Bezemer » Fri May 03, 2013 2:05 pm

Patrick,

Your making good progress. Your necks (all three) look great.

Hans
User avatar
Hans Bezemer
 
Posts: 372
Joined: Sat May 26, 2012 1:01 am
Location: The Netherlands

Re: Patrick DeGreve's travel guitar

Postby Mark Swanson » Fri May 03, 2013 3:06 pm

What scale length did you use, and how come the bridges are so far down on the top? That will greatly impede the response and volume on a top that is already small.
    Mark Swanson, guitarist, MIMForum Staff
User avatar
Mark Swanson
 
Posts: 1908
Joined: Thu Jan 05, 2012 11:11 am
Location: Grand Rapids, Michigan USA

Re: Patrick DeGreve's travel guitar

Postby Patrick DeGreve » Fri May 03, 2013 9:36 pm

Thanks Hans. Mark I am using a 24.5" scale length, and the overall guitar length is 34". I based the travel guitars on a guitar made by a San Diego company called Go-Guitars. One of my co-workers brought a go-guitar to work, and we all played it and liked it overall. It sounded good for such a small guitar, and played very good. The one thing I didn't like was that it had no waist, and that made it lean forward in your lap. So when I designed the travel guitars I added a waist, and enlarged the lower bout slightly. I finished a travel guitar about two months ago and took it to work, and most everybody liked its playability, and sound. It does have a bright sound, not a lot of bass but very pleasant. I thought about moving the bridge more into the center of the soundboard, but I would have to shorten the scale or lengthen the guitar overall. That would take away from it's function as a travel guitar, small enough to take camping or backpacking etc.
User avatar
Patrick DeGreve
 
Posts: 307
Joined: Mon Jan 09, 2012 2:19 pm

Re: Patrick DeGreve's travel guitar

Postby Warren May » Sat May 04, 2013 2:04 am

Starting to come together, Patrick. I like the simple look of your cutouts and the rosettes look really nice. We're all anxious to hear how they sound. I'd seen an acoustic travel guitar with bridge placement something like yours and after looking on Google I think it might have been a Washburn Rover. I wouldn't expect a big booming dreadnaught sound from it but travel guitars are always a little compromise to get the size down. Really great work and I doubt anyone would know it's reclaimed flooring :)
Warren May
 
Posts: 246
Joined: Fri Aug 10, 2012 7:00 pm

Re: Patrick DeGreve's travel guitar

Postby Patrick DeGreve » Mon May 06, 2013 2:20 pm

Thanks Warren, when I first started thinking about making guitars a few years ago, I read that Oak was not used for guitars because it was a "dead" wood. Now I see a few wood suppliers selling guitar sets with oak. This challenge has given me an chance to see what I it sounds like. Last week I cut braces from the pine for the backs, pre-shaped them, and glued the up using the go-bar press.
Attachments
3backbraces.jpg
User avatar
Patrick DeGreve
 
Posts: 307
Joined: Mon Jan 09, 2012 2:19 pm

Re: Patrick DeGreve's travel guitar

Postby Patrick DeGreve » Mon May 06, 2013 2:29 pm

I decided to add a JJB Electronics transducer pickup in the oak steel string travel guitar. I am not going to put a pickup in the nylon string guitar. I used their 2 transducer standard unit $19.95. I have used a few of their three transducer units and they worked fine. I am not going to install a pre amp in this guitar, (they say you don't need one for this system), we will see. I have a very small Fender battery operated amp that is so light and small you could put it in your backpack easy.
Attachments
3jjbpickup.jpg
User avatar
Patrick DeGreve
 
Posts: 307
Joined: Mon Jan 09, 2012 2:19 pm

Re: Patrick DeGreve's travel guitar

Postby Patrick DeGreve » Mon May 06, 2013 2:30 pm

I next glued the backs onto the travel guitars, again using the go-bar press.
Attachments
3glueback.jpg
User avatar
Patrick DeGreve
 
Posts: 307
Joined: Mon Jan 09, 2012 2:19 pm

Re: Patrick DeGreve's travel guitar

Postby Patrick DeGreve » Mon May 06, 2013 2:32 pm

Here is a shot of the backs of the two travel guitars.
Attachments
3viewbacks.jpg
User avatar
Patrick DeGreve
 
Posts: 307
Joined: Mon Jan 09, 2012 2:19 pm

Re: Patrick DeGreve's travel guitar

Postby Patrick DeGreve » Mon May 06, 2013 2:33 pm

Using a jig I made, I routed the recess for the bindings I pre-bent with the fox style bender.
Attachments
3route1.jpg
User avatar
Patrick DeGreve
 
Posts: 307
Joined: Mon Jan 09, 2012 2:19 pm

Re: Patrick DeGreve's travel guitar

Postby Patrick DeGreve » Mon May 06, 2013 2:34 pm

Here is a close-up of the recess on the pine guitar.
Attachments
3route.jpg
User avatar
Patrick DeGreve
 
Posts: 307
Joined: Mon Jan 09, 2012 2:19 pm

Re: Patrick DeGreve's travel guitar

Postby Patrick DeGreve » Mon May 06, 2013 2:37 pm

I am using rosewood bwb binding I bought in bulk on Ebay for both guitars. I like the contrast of the dark binding on the light woods. Here I have glued and taped on the bindings.
Attachments
3tape.jpg
User avatar
Patrick DeGreve
 
Posts: 307
Joined: Mon Jan 09, 2012 2:19 pm

Re: Patrick DeGreve's travel guitar

Postby Patrick DeGreve » Mon May 06, 2013 2:39 pm

After the bindings dried I scraped and sanded the two guitars. They are now ready for the necks.
Attachments
3sanded.jpg
User avatar
Patrick DeGreve
 
Posts: 307
Joined: Mon Jan 09, 2012 2:19 pm

Re: Patrick DeGreve's travel guitar

Postby Jason Rodgers » Mon May 06, 2013 4:20 pm

I like how these are turning out. Just an observation: I understand that they are travel instruments, and so need to withstand some knocks, not to mention climate swings, but these little guys look really heavily built. Maybe that's the point?
-Ruining perfectly good wood, one day at a time.
Jason Rodgers
 
Posts: 1542
Joined: Fri Jan 06, 2012 4:05 pm
Location: Portland, OR

Re: Patrick DeGreve's travel guitar

Postby David Ackley » Mon May 13, 2013 10:30 pm

I too am really liking the looks of both of these guitars. Nice use of the wedge-shaped back strips.
David Ackley
 
Posts: 33
Joined: Sat Jan 07, 2012 3:19 am
Location: Moscow, Idaho

Re: Patrick DeGreve's travel guitar

Postby Samuel Hartpence » Thu May 16, 2013 1:11 pm

How about some more details on the binding channel jig. I'm in need of something similar.
Samuel Hartpence
 
Posts: 94
Joined: Mon Jan 09, 2012 11:32 am

PreviousNext

Return to The "Reclaimed Materials" Challenge (closed)

Who is online

Users browsing this forum: No registered users and 1 guest

Your purchase from these sites helps support the MIMForum, but only if you start at the links below!!!
Amazon music     Amazon books     Amazon tools     Rockler tools     Office Depot    

The MIMF is a member-supported forum, please consider supporting us with a donation, thanks!
 • Book store • Tool store • Links •