Fitting bass neck to body fender style

If you have a string instrument of any kind that needs fixing, a mistake you made in building a new instrument that you need to "disappear," or a question about the ethics of altering an older instrument, ask here. Please note that it will be much easier for us to help you decide on the best repair method if you post some pictures of the problem.

Fitting bass neck to body fender style

Postby Jedi Clampett » Thu Mar 17, 2016 4:43 pm

Just curious as to what you do to fit a slightly oversized Precision bass neck to a slightly undersized fender style body?
I assume that I just take a wood file and make the same number of strokes on each side of the bass cavity until the neck drops in, but you may have some other way. This of course with tuners, bridge installed and outer strings.
Jedi Clampett
 
Posts: 164
Joined: Thu Nov 21, 2013 12:55 am

Re: Fitting bass neck to body fender style

Postby Brian Evans » Thu Mar 17, 2016 7:40 pm

I would probably take the neck down a bit, it being easier to get at. I probably would have discovered this before it had strings on it. Keeping it square to the body, so the strings lay properly on the neck, is very important.
Brian Evans
 
Posts: 720
Joined: Sat Aug 30, 2014 8:26 am
Location: Tatamagouche, Nova Scotia

Re: Fitting bass neck to body fender style

Postby David King » Thu Mar 17, 2016 8:10 pm

Don't remove the original neck finish if you can help it unless you enjoy refinishing necks. If you do remove the finish then straighten out the fingerboard edges while you are at it and think about re-carving the neck to a thinner profile if it's one of those monstrosities from Warmoth.

Otherwise:
Clean up the sides of the neck with fine sandpaper on a straight board to clean up any finish drips or random bumps.
Create an accurate cardstock or thin plywood template of the outline of the neck heel with a centerline marked.
Mark the centerline on the bass body with masking tape between the center line of the neck pocket and the middle of the bridge. If the bridge isn't mounted yet use the centerline of the pickups, the strap button hole or a full sized paper plan to establish it.
Line up the centerlines and score the new neck pocket lines on the body and trim the excess with a sharp, wide chisel.
Check with a small square to make sure that your chisel strokes are on target.
David King
 
Posts: 2448
Joined: Sat Jan 07, 2012 10:01 pm
Location: Portland, OR

Re: Fitting bass neck to body fender style

Postby Paul Kincaid » Thu Mar 24, 2016 1:01 am

I prefer to fit the body to the neck, at least when that is appropriate and especially if a lot of material must be removed. If the neck must be fit to the body, I would tend to work wherever it will be the least seen and the least material removed. If the bass side of the neck fits well and is aligned with the bridge well, then a small amount of material may be removed from the treble side to fit the smaller and less visible side of the neck pocket. If the neck does not align well with the bridge when touching the bass side of the pocket then be sure to make the contact points with the pocket as large and even as possible.
Paul Kincaid
 
Posts: 37
Joined: Wed May 23, 2012 11:42 am

Re: Fitting bass neck to body fender style

Postby Jedi Clampett » Tue Mar 29, 2016 9:25 pm

It worked, I scraped the neck pocket of excess finish, a little sanding and it fit thanks for everything
Jedi Clampett
 
Posts: 164
Joined: Thu Nov 21, 2013 12:55 am


Return to String Instrument Repair: Practical and Political Issues

Who is online

Users browsing this forum: No registered users and 4 guests

Your purchase from these sites helps support the MIMForum, but only if you start at the links below!!!
Amazon music     Amazon books     Amazon tools     Rockler tools     Office Depot    

The MIMF is a member-supported forum, please consider supporting us with a donation, thanks!
 • Book store • Tool store • Links •