tone and volume on top plate actual effect?

Please put your pickup/wiring discussions in the Electronics section; and put discussions about repair issues, including fixing errors in new instruments, in the Repairs section.

tone and volume on top plate actual effect?

Postby Brian Evans » Wed Sep 12, 2018 8:50 am

To me it's almost an insult to put the tone and volume pot's on the top of a truly acoustic archtop - but is it really? Has anyone ever done a proper A-B comparison of the same top before and after controls have been fitted? Is the impact negligible, dramatic, you could kind of tell in an A-B test but not after a few days to forget the exact tone quality?

One reason I ask is that there seems to be about zero market for true acoustic archtops, even Benedetto rarely gets a commission for one. The reason, of course, is that mostly pro players buy them and mostly pro players need a pickup and a guitar biased to perform on stage at a certain volume. I am thinking of adding a neck mounted floating pickup to my latest build, and since I don't use a finger rest was leaning towards the top mounted controls, which I actually quite like as a period visual statement. But I cringe when I think of drilling the top and adding the mass of the potentiometers and other wiring inside the box.

Brian
Brian Evans
 
Posts: 689
Joined: Sat Aug 30, 2014 8:26 am
Location: Tatamagouche, Nova Scotia

Re: tone and volume on top plate actual effect?

Postby Alan Carruth » Wed Sep 12, 2018 12:19 pm

Pots don't add the mass that a P/U does, but I know how you feel.

Added mass on the top does help to reduce feedback. That's a problem when you have to compete with a sax or trumpet. It may be why the players like to ones with top-mount pickups, even though they don't have the acoustic sound.

IMO the rule is: "if the room can hear the guitar, the guitar can hear the room". With enough gain in the loop anything will feed back. There are ways to deal with it, up to a point, but there are limits.

I guess the next question is, what do you have against finger rests? I've used them to mount the controls for a pickup that either mounts to the neck or floats off the finger rest, and sometimes both, and they do make a handy place for controls.
Alan Carruth
 
Posts: 818
Joined: Sun Jan 15, 2012 1:11 pm

Re: tone and volume on top plate actual effect?

Postby Barry Daniels » Wed Sep 12, 2018 12:41 pm

Slide pots under the edge of a pickguard are a very slick solution.
MIMF Staff
Barry Daniels
 
Posts: 1946
Joined: Thu Jan 05, 2012 10:58 am
Location: Houston, Texas

Re: tone and volume on top plate actual effect?

Postby Brian Evans » Wed Sep 12, 2018 1:12 pm

My playing style suffers if I have a finger rest, I anchor there and it screws me up. I could probably get used to it, but my thought process kind of said "wait, maybe the other isn't so bad after all. You don't actually know, you just assume - and you know what that means..."

Allan, when I toured Benedetto in the spring they had exactly one acoustic guitar in the house - the 50th anniversary model they just finished making. Every other guitar had a set-in pickup. They do the bracing completely differently - they use heavier "parallel" bracing, with cross-braces where the pickups go, and rout the pickup hole to just go into the braces, so the pickup is surrounded by brace on all sides. I'm going to guess and say that over half their production (around 10 guitars a month) are laminated top and back plates. They do their own laminating with three layers of 1/16" thick veneer.
Brian Evans
 
Posts: 689
Joined: Sat Aug 30, 2014 8:26 am
Location: Tatamagouche, Nova Scotia

Re: tone and volume on top plate actual effect?

Postby Barry Daniels » Thu Sep 13, 2018 12:21 pm

Brian, this is very interesting and confirms what I have seen with a couple of other acoustic archtop builders that I know well.

So, in that vein, you may want to make your own version of a more electric, stiffer archtop and install the electronics in the top and not worry about acoustic effects.

A couple of questions, did the Benedetto factory also put potentiometers in the top and are these electric archtops thinner than a full-on acoustic?
MIMF Staff
Barry Daniels
 
Posts: 1946
Joined: Thu Jan 05, 2012 10:58 am
Location: Houston, Texas

Re: tone and volume on top plate actual effect?

Postby Alan Carruth » Thu Sep 13, 2018 1:49 pm

It's a continuum from the full acoustic all the way to solid body, and you can work anywhere you want along the line.

I made a couple of acoustic electric archtops some years ago. Those both had finger rests where I mounted the controls.I had a heavy wood beam that ran from the neck block to the tail block, and mounted the pickups on that. The top was more less 'normal' with holes cut in it for the pickups to poke through. On the first one I used a spruce top, but it was too active, so I made another with a maple top and only on F-hole. It worked pretty well, but UPS destroyed it. The small hole and heavy top kept feedback down, but the top was still 'tuned' and active enough to contribute some color to the tone. I found it helped to keep the sound output low in the low range; it seems to keep more sound in the strings for the pickup to pick up.

The upper bout part of the top doesn't move as much as the rest, and might make a good place to mount controls. I've done that on flat tops.
Alan Carruth
 
Posts: 818
Joined: Sun Jan 15, 2012 1:11 pm

Re: tone and volume on top plate actual effect?

Postby Jim Hepler » Thu Sep 13, 2018 7:21 pm

Brian, I know this doesn't answer your question, but you could just wire a floating pickup directly to the output. Set the volume and tone on the amp where you want it. If you need to make adjustments on the fly, I actually prefer a volume pedal since my hands are busy when I'm playing. I'm more likely to want to adjust volume than tone when I play, but there are also various switchable eq pedals that could work for tone adjustments. It's true this might be a hard sell for generic customers, but it's very workable if it's for you. I suppose another option would be to put the controls on the side like you see on acoustic guitars with pickups. Taylor and others use low profile knobs and no visible plastic box, and the look is pretty unobtrusive. Don't know where you find those parts, but it's another thought.

As to your original question about the effect of putting pots on the top, I don't really know. My prejudice is against it, but I have no actual evidence to support that. I don't mind a pick guard so I'm inclined to favour putting those thumbwheels (schatten?) under the pick guard if I want on-guitar controls. My 2 cents.
jim
Jim Hepler
 
Posts: 79
Joined: Thu Sep 13, 2012 2:15 pm

Re: tone and volume on top plate actual effect?

Postby Mike Conner » Fri Sep 14, 2018 9:05 am

Brian,
I also dislike finger rests or floating pickguards on archtops. For me they are in the way and a source for rattles or buzzes.

I have been using Schatten thumbwheel pots purchased through StewMac and installing them on the inside lip of the bass side F-hole. They sell a kit that includes the capacitor (of course you could swap cap out for another preference).

https://www.stewmac.com/Pickups_and_Electronics/Components_and_Parts/Potentiometers/Schatten_Thumbwheel_Controls.html

For my most recent installation I installed the pots in a modified plastic box, shielded with copper tape:
N7-301 Thumbwheels on box lid.JPG


With the guitar completed, they look like this:
N7-132 Pots in f hole.JPG


This guitar is actually a stereo output. A surface mounted StewMac Golden Age humbucker is wired to the tip and using the thumbwheel pots. The ring connection goes to JJB piezo transducers. I removed the HB pickup legs and mounted to the front plate using heavy duty exterior grade mounting tape with no window cut in the plate for the pickup:
N7-131 Side view HB and neck extension.JPG


I setup and play my builds in the white, make adjustments, then disassemble for finishing. I did not notice a big difference in acoustic tone with the humbucker surface mounted. I assume it is because the humbucker is basically right above the upper arms of the X brace and this area of the front plate is not a big contributor to volume or acoustic tone.

Hope this helps!
//mike
Mike Conner
 
Posts: 128
Joined: Wed Feb 08, 2012 8:12 pm
Location: Seneca SC

Re: tone and volume on top plate actual effect?

Postby Chuck Morrison » Fri Sep 14, 2018 10:55 am

I also share an aversion to cutting holes and mounting pickups onto a carved arch top. It just seems wrong to put so much work into it and then defile it with electronics. I do realize the economic necessity, but I've always felt that an acoustic guitar was a different beast from an electric guitar and by necessity needs to be built differently. Feedback issues if nothing else seem to demand it. Even my old Guild CE-100D plywood archtop would feedback horribly. Still, I prefer a neck mounted pickup for arch tops on general principles with pickguard mounted pots. However I don't like having a pickguard in the way when finger picking.

As far as sound goes, I wouldn't expect much difference in the acoustic sound from a pickup near the neck block, but I would be wary of anything near the bridge. The other question though is what mounting a pickup on a mobile part of the top do to the sound from the pickup? I think most would agree that the ideal is a very stable pickup location and let the string do the moving. Moving the pickup around at the same time could have interesting and undesired effects. Maybe that's why my old Guild fed back so badly.

I always liked the Guild George Barnes acousti-lectric concept, which had the pickups mounted on supports under the soundboard, poking up through (sound) holes in the top, so the pickups never touched the top. They looked a bit odd at the time with no F holes, but maybe not so odd 50 years later. It might be time to revisit that concept.
User avatar
Chuck Morrison
 
Posts: 67
Joined: Tue Jan 10, 2012 6:17 pm
Location: Colorado, USA

Re: tone and volume on top plate actual effect?

Postby Randolph Rhett » Fri Sep 14, 2018 11:42 am

My arch top builds are all “acoustic”, even some nylon string. But you are right, there is precious little market for that. For 95% of all arch top buyers (which is already a tiny number) the arch top guitar is a Cadillac of bling ELECTRIC guitar.

There is good reason for that. Most acoustic guitar players want a guitar to accompany vocalists. It’s hard to do better than a dreadnought with its boomy lows and shimmering highs. Acoustic arch tops lend themselves to the far more difficult task of solo guitar playing. More like a classical guitar, but without the heritage, history, or body of work.

As an electric guitar players have many examples of talented players. From Charlie Christian to Pat Methaney you have a wide variety of guitar heroes on electric arch tops.

My personal philosophy was to choose: do I build acoustic guitars for me and three or four other people a year, or somehow try to capture a slice of the electric guitar market? I’m not sure how anyone can make a living as a luthier today, but I’m grateful I don’t have to. That means I build the guitars I want to play, and consider myself blessed to sell a few here and there. Two pickups and four controls are NEVER going to live on the top of one of my guitars*

*of course, I was persuaded to make one just like that a few years ago for a charity auction, so I guess “never” is too strong a word ;-)
User avatar
Randolph Rhett
 
Posts: 324
Joined: Mon Aug 06, 2012 5:19 pm
Location: San Diego, CA

Re: tone and volume on top plate actual effect?

Postby Chuck Morrison » Fri Sep 14, 2018 12:48 pm

My choice as well, and yes there are not nearly enough Maybelle Carters around these days.
User avatar
Chuck Morrison
 
Posts: 67
Joined: Tue Jan 10, 2012 6:17 pm
Location: Colorado, USA

Re: tone and volume on top plate actual effect?

Postby Rick Milliken » Fri Sep 14, 2018 10:09 pm

Brian, thanks for asking the question! The responses have been very informative. But, mostly I'm glad to know I'm not the only one that struggles with the notion of drilling holes and adding buttons, switches and wiring to my "pride and joy"!
Rick Milliken
 
Posts: 9
Joined: Wed May 31, 2017 10:05 pm
Location: Okotoks, AB, Canada

Re: tone and volume on top plate actual effect?

Postby Brian Evans » Sat Sep 15, 2018 8:27 am

I think I will get some modeling clay or double sided tape and stick a mass equivalent to the pots, knobs and wiring to the location I have in mind. I guess the thing is I know lots of ways to get the job done without the holes, but if you are recreating a period of history the thing should look the part, so it's a visual element that I am curious about as well as all the rest. I probably won't do it, at the end of the day I never play any of my electric guitars anymore.
Brian Evans
 
Posts: 689
Joined: Sat Aug 30, 2014 8:26 am
Location: Tatamagouche, Nova Scotia

Re: tone and volume on top plate actual effect?

Postby Alan Carruth » Wed Sep 19, 2018 12:15 pm

I'm on the road, and somewhat preoccupied, or I would have thought of it sooner: poster adhesive is far better than modeling clay when you want to try the effect of added mass. Modeling clay is made with mineral oil, which leaches out into the wood and causes all sorts of problems. The goo in poster adhesive pretty much stays put.
Alan Carruth
 
Posts: 818
Joined: Sun Jan 15, 2012 1:11 pm


Return to Archtop Guitars and Bass Guitars

Who is online

Users browsing this forum: No registered users and 3 guests

Your purchase from these sites helps support the MIMForum, but only if you start at the links below!!!
Amazon music     Amazon books     Amazon tools     Rockler tools     Office Depot    

The MIMF is a member-supported forum, please consider supporting us with a donation, thanks!
 • Book store • Tool store • Links •