StewMac tools            

SIX ...

Please put your pickup/wiring discussions in the Electronics section; and put discussions about repair issues, including fixing errors in new instruments, in the Repairs section.

Re: SIX ...

Postby Beate Ritzert » Mon Aug 14, 2017 6:43 pm

Well, i am going to use 0.095" flatwounds on that bass. Simply because i would like to have a real bass sound and not some guitar in a very low tuning.

I just checked: a .080" Daddario chrome string fits through the hole of a chinese copy of a Schaller guitar tuner. But nothing thicker - that's the limit.
User avatar
Beate Ritzert
 
Posts: 413
Joined: Thu Aug 02, 2012 8:20 am
Location: Germany

Re: SIX ...

Postby Beate Ritzert » Wed Aug 16, 2017 6:39 pm

Image

Slow progress in carving the top... This irregularly grown wood is sometimes tricky to work on. Luckily this is "just" pear wood, roughly as hard and strong as maple but easier to cut with chisels and planes.
User avatar
Beate Ritzert
 
Posts: 413
Joined: Thu Aug 02, 2012 8:20 am
Location: Germany

Re: SIX ...

Postby Beate Ritzert » Mon Nov 27, 2017 10:51 am

Outer shape of the top roughly carved. My finger tips tell me there is still some symmetry. But it is really hard so see; the shape is about as "exact" as that of my first archtop. Well i think i'd mark some isolines with a (pencil) marker gauge and try to get it a bit better before i start with the inner arch.

Image

Image

Image
User avatar
Beate Ritzert
 
Posts: 413
Joined: Thu Aug 02, 2012 8:20 am
Location: Germany

Re: SIX ...

Postby Barry Daniels » Thu Nov 30, 2017 9:39 pm

Bob Benedetto recommends a desk lamp set very low almost at bench top height which will show the arch much better. Turn off the overhead lights in the workshop to enhance the effect. I like to stand back and squint my eyes a bit so I am looking at general shapes instead of details.
MIMF Staff
Barry Daniels
 
Posts: 1734
Joined: Thu Jan 05, 2012 10:58 am
Location: Houston, Texas

Re: SIX ...

Postby Geoff St. Germaine » Tue Dec 12, 2017 6:11 pm

I use a magnetic LED work light that I can move around to the different legs of the table I use for carving the tops on my guitars with the shop lights out as Barry describes. I wind up rotating the body around quite a lot when finalizing the arch to look from many different angles. When I first started making archtops I tried with pin gauges and templates and a few other methods and while they got me roughly in the ballpark of a symmetric carve, the low angle point source light worked far better and is honestly easier to work with.
Geoff St. Germaine
 
Posts: 21
Joined: Sun Jun 23, 2013 6:00 pm

Re: SIX ...

Postby Beate Ritzert » Wed Dec 13, 2017 6:13 pm

Thanks for the hints. I'll try it. I put the top aside and started to carve the bottom. Same profile, again using my templates to get very rough orientation. This time i started with the horns - and i'm enjoying the speed and the ease of the progress (alder...).

<offtopic>

But progress will be slowly - i have to travel 50 km to that room, and i am there only occasionally, when i need to organize something for my new old house (i guess the small house in front is at least 150 years old):

DSC_3633.JPG


</offtopic>
User avatar
Beate Ritzert
 
Posts: 413
Joined: Thu Aug 02, 2012 8:20 am
Location: Germany

Previous

Return to Archtop Guitars and Bass Guitars

Who is online

Users browsing this forum: No registered users and 1 guest

Your purchase from these sites helps support the MIMForum, but only if you start at the links below!!!
Amazon music     Amazon books     Amazon tools     Rockler tools     Office Depot    

The MIMF is a member-supported forum, please consider supporting us with a donation, thanks!
 • Book store • Tool store • Links •