StewMac tools

Breakover angle at nut

Please put your pickup/wiring discussions in the Electronics section; and put discussions about repair issues, including fixing errors in new instruments, in the Repairs section.

Breakover angle at nut

Postby George Reiswig » Wed Oct 05, 2016 11:57 am

I use two instruments that both have some fairly heavy wound strings. On my baritone acoustic, the 6th string is a .070", and on my standard-scale Lowden where I regularly tune the 6th down to a B, I use either a standard .056" or even a .060".

These strings are thick enough that they don't easily bend over the angle of the nut if I do the windings around the tuner the way I am accustomed to doing them: with the lowest winding being the "exit" winding such that the string goes from basically the bottom of the post to the nut. As a result, the action is increased. I can force a bend at the nut once tuned, but for example on my Lowden I change tunings a great deal, ranging from that low B up to E. A permanent bend there causes issues.

Or...I could change the way I wind the string around the tuning post, so that the exit winding is higher, decreasing the angle over the nut. This does seem to help a bit, but it got me thinking about whether there are other factors that might be affected doing this? Is there an optimal break over angle? Is there a generally agreed proper direction to wind the string around a tuning post?
George Reiswig
 
Posts: 10
Joined: Fri Aug 12, 2016 8:51 pm

Re: Breakover angle at nut

Postby Brian Evans » Wed Oct 05, 2016 2:25 pm

I don't know about optimal angle, but I do know a friend recently built a guitar with too shallow a break angle too shallow a headstock angle, really) and had a buzz that was very hard to diagnose and fix. A lot might depend on headstock angle to start with, and distance from the nut to the post - all variables in every build.

Brian
Brian Evans
 
Posts: 516
Joined: Sat Aug 30, 2014 8:26 am
Location: Tatamagouche, Nova Scotia

Re: Breakover angle at nut

Postby Glenn Ohman » Wed Nov 16, 2016 9:15 am

I think it should more or less match the break angle at the headstock.

Glenn
Glenn Ohman
 
Posts: 10
Joined: Wed Dec 23, 2015 9:21 pm

Re: Breakover angle at nut

Postby Rodger Knox » Wed Nov 16, 2016 12:30 pm

Minimum "effective" break angle is about 6°. Less than that is not enough, and with the OP's heavy string issue I'd guess "optimal" would be between 6° and 8°.
I also wind the strings down the post, which is pretty typical for those who pay attention to that kind of thing, but that's just to increase the break angle. I see no reason you shouldn't wind the strings up the post to reduce the break angle as long as you don't go too far.
Normally, more break angle does not cause problems, but with heavy strings that may not be true.
A man hears what he wants to hear, and disreguards the rest. Paul Simon
Rodger Knox
 
Posts: 484
Joined: Mon Jan 09, 2012 2:02 pm
Location: Baltimore, Maryland

Re: Breakover angle at nut

Postby Steven Smith » Wed Nov 16, 2016 1:53 pm

Per my training, the breakover angle on the nut should vary from perhaps 5 to 7 degrees at the string entry to a few degrees less than the breakover angle of the headstock. This is facilitate smooth string movement through the nut and to prevent buzzing.
Steven Smith
 
Posts: 145
Joined: Fri Jan 06, 2012 5:01 pm
Location: East Tennessee

Re: Breakover angle at nut

Postby Gordon Bellerose » Wed Nov 16, 2016 3:10 pm

The shape of the nut might also affect the way the string works there.
Is this a "Fender" type nut? Very thin, with a bit of fret board in front?
Or is is a "Gibson" type, resting against the front edge of the fret board?

If it is a "Gibson" type, you should be able to shape the slot so that the fret board side is flat along the plane of the fret board, and the trailing edge slopes down toward the tuner. This gives the string a nice rounded "ramp" in which to work.
I need your help. I can't possibly make all the mistakes myself!
Gordon Bellerose
 
Posts: 926
Joined: Wed May 30, 2012 11:47 pm
Location: Edmonton AB. Canada


Return to Flat-Top Acoustic Guitars and Bass Guitars

Who is online

Users browsing this forum: Google [Bot] and 2 guests

Your purchase from these sites helps support the MIMForum, but only if you start at the links below!!!
Amazon music     Amazon books     Amazon tools     Rockler tools     Office Depot    

The MIMF is a member-supported forum, please consider supporting us with a donation, thanks!
 • Book store • Tool store • Links •