StewMac tools

Radius of domed back

Please put your pickup/wiring discussions in the Electronics section; and put discussions about repair issues, including fixing errors in new instruments, in the Repairs section.

Radius of domed back

Postby Chris Lounsbury » Sun May 29, 2016 10:03 pm

Let's set down a few givens, and then I'll pose my question.

I build using outside molds and radius dishes. To date I have built with 30' radius imparted to the soundboard and 15' radius imparted to the back. My backs have been braced in the standard ladder manner, but with braces tall enough to make it all pretty rigid and reflective. I now wish to make some backs somewhat more flexible and resonant.

I already have another bracing scheme in mind to try. The question for the day is this - If I also use the flatter 30' radius for the back, should I look out for wood movement trouble (ie. cracking)? The potential problem that comes to mind is, back material is frequently very far from the perfectly quartersawn ideal we look for in soundboards, and the flatter the cut, the more the back will expand and contract.

I do control humidity in my shop and maintain RH between 35%-45%. I don't really feel I am facing a problem here but I would welcome your advice and experience.
Chris Lounsbury
 
Posts: 16
Joined: Thu Feb 23, 2012 12:37 pm

Re: Radius of domed back

Postby Clay Schaeffer » Mon May 30, 2016 10:09 am

The older Martin guitars used wide flat braces ( approx 1/4 in H X 3/4 in W) in the lower bout of the back, which is what I do. I think this helps the back move more easily with humidity changes. I doesn't make sense to me to use tall thin braces that restrict movement in wide areas already dealing with cross grain glued braces.
Off quarter wood is always going to be less stable than vertical grain. I don't think the change in radius will make much difference if it is still locked in by tall rigid bracing.
Clay Schaeffer
 
Posts: 1037
Joined: Fri Jan 06, 2012 12:04 pm

Re: Radius of domed back

Postby Chris Lounsbury » Mon May 30, 2016 11:29 am

Part of my change in approach is to move away from the tall braces, particularly in the lower bout.

Maybe I can rephrase my question more succintly:

If I loosen up my bracing scheme and move from a 15' radius back to a 30' radius back, is there some combination of material choice & cut which might get me in trouble with insufficient latitude for shrinkage across the grain? Same point about building in 35% - 45% RH applies.
Chris Lounsbury
 
Posts: 16
Joined: Thu Feb 23, 2012 12:37 pm

Re: Radius of domed back

Postby Alan Carruth » Mon May 30, 2016 12:51 pm

The flatter back should be somewhat more flexible, but I'm not sure if it will be all that much more.

I've used a lot of different back brace schemes over the years, trying to make a back that was 'active' in the low range and more 'reflective' above that. Several yeas ago I switched back to ladder bracing. I use a 'free' plate tuning method, and what I found was that the lower two braces (of four) on the back really had to be shaved down low to get it to work the way I wanted it to. With narrow braces this meant there wasn't a lot of wood there. so I went to the Martin setup of low, wide braces below the waist. With a 15' back radius and braces that are about 9mm tall in the center the ends come out to just about the correct height to inlet. This works well. Sometimes there are reasons behind the traditions!
Alan Carruth
 
Posts: 743
Joined: Sun Jan 15, 2012 1:11 pm


Return to Flat-Top Acoustic Guitars and Bass Guitars

Who is online

Users browsing this forum: No registered users and 3 guests

Your purchase from these sites helps support the MIMForum, but only if you start at the links below!!!
Amazon music     Amazon books     Amazon tools     Rockler tools     Office Depot    

The MIMF is a member-supported forum, please consider supporting us with a donation, thanks!
 • Book store • Tool store • Links •