Holding bodies and necks during finishing

TEST ON SCRAP FIRST! If your question is about repair work, either regluing or refinishing, please post it in our Repair Section.
Post Reply
Andrew McSpadden
Posts: 80
Joined: Wed Jan 02, 2013 4:28 pm
Contact:

Holding bodies and necks during finishing

Post by Andrew McSpadden »

I am spraying more and am tired of coat hangers and screws to hang my stuff. I have worked in several factories and seen some neat ways of holding and hanging parts during finishing. Anybody care to share what they use or a pic of a great idea?

Thanks in advance!
David King
Posts: 2690
Joined: Sat Jan 07, 2012 10:01 pm
Location: Portland, OR
Contact:

Re: Holding bodies and necks during finishing

Post by David King »

I used a system my friend with the spray booth uses. It's 3/4" galvanized electrical conduit, hammered flat at one end and screwed to a block of wood that can key into some part of the guitar body or neck and get fixed there. You can slip the pipe over a mandrel or hang it from a wire when you aren't holding it and turning the part as you spray it. There are mandrels sticking out at various angles around the room so you can spray a stack of parts and set them up to dry or turn them frequently to stop runs from forming.
User avatar
Dan Smith
Posts: 346
Joined: Mon May 18, 2015 9:33 pm
Location: Texas

Re: Holding bodies and necks during finishing

Post by Dan Smith »

I install an eyelet into the bottom where the strap lock will be.
I found hanging the guitar upside down easier to manipulate when spraying.
Ever-body was kung fu fight-in,
Them kids was fast as light-nin.
Brian Evans
Posts: 922
Joined: Sat Aug 30, 2014 8:26 am
Location: Tatamagouche, Nova Scotia

Re: Holding bodies and necks during finishing

Post by Brian Evans »

I typically hang the neck, but I use a stand for the body.
Attachments
IMG_0146.JPG
User avatar
Peter Wilcox
Posts: 1317
Joined: Sun Jan 08, 2012 1:31 am
Location: Northeastern California

Re: Holding bodies and necks during finishing

Post by Peter Wilcox »

I spray everything horizontally - fewer runs that way for me. I attach a stick to the screw holes of the the neck pocket or the neck heel, or the bolt holes on bolt on necks and bodies. The stick is wedged in a hole in a riser attached to an old rotating TV stand. The part can be rotated horizontally or flipped as needed to spray, and I can just stand in one place (where the angle of illumination is best.) I have to spray outside, and I can set it up or tear it down in less than 5 minutes.
Attachments
spray-setup.jpg
Maybe I can't fix it, but I can fix it so no one can fix it
User avatar
Steve Sawyer
Posts: 965
Joined: Wed Jan 02, 2013 2:20 pm
Location: Detroit, Michigan

Re: Holding bodies and necks during finishing

Post by Steve Sawyer »

I have "designs" for the mounting I'm going to use for the current build, and will share that when I get it done. One question I have though is that I'm assuming a set-neck guitar is finished with the neck assembled; I can't see trying to clamp and glue a finished neck. That assumption is what is leading me to design something that locks into one of the pickup cavities.

There might be a rotisserie motor involved now that I've seen someone do that! :)
==Steve==
User avatar
Barry Daniels
Posts: 3186
Joined: Thu Jan 05, 2012 10:58 am
Location: The Woodlands, Texas

Re: Holding bodies and necks during finishing

Post by Barry Daniels »

You can spray the parts separately if you want to. Just use some masking tape.
MIMF Staff
User avatar
Steve Sawyer
Posts: 965
Joined: Wed Jan 02, 2013 2:20 pm
Location: Detroit, Michigan

Re: Holding bodies and necks during finishing

Post by Steve Sawyer »

Barry Daniels wrote:You can spray the parts separately if you want to. Just use some masking tape.
Unfortunately, I don't spray - don't have the facilities.

My concern isn't so much for the application though, just damaging the finish in the process of assembly.
==Steve==
Andrew McSpadden
Posts: 80
Joined: Wed Jan 02, 2013 4:28 pm
Contact:

Re: Holding bodies and necks during finishing

Post by Andrew McSpadden »

Thanks to everyone that replied! I look forward to more of your ideas.
Carl Dickinson
Posts: 94
Joined: Fri Feb 08, 2019 5:38 pm
Location: Forest Ranch, California

Re: Holding bodies and necks during finishing

Post by Carl Dickinson »

Here's some pics of my spray support. Pallet, casters, 6'x post, small vise, StewMac holder.
PICT0260 (2).JPG
PICT0259.JPG
Post Reply

Return to “Glues and Finishes”