Hi Guys,
I'm new here at MIMF. I need some expert advice on the pot wiring for my Warmoth. A while back my guitar wasn't sending a signal out to the jack. I knew that it was a problem with one of the pots because it would cut in and out when I turned the volume pot. I took the plate off to take a look and I noticed there was a broken solder joint on the back of volume pot where 3 wires joined. I tried re soldering them but I couldn't fix it because of the massive buildup of solder on the joint. Instead I cut the wires and soldered two on the right side (pic) and one on the left side of the pot.
Now the guitar has a signal out but the pot is apparently bypassed. The pot seemingly has no effect on the signal now. Can someone please explain to me what I did wrong and how I can fix it?
Thank you very much ahead of time! I can fix a lot of things but guitar electronics confuse me.
https://www.dropbox.com/s/b4kd6uwx4hw6t ... r.png?dl=0
Volume Pot Wiring
- Mark Swanson
- Posts: 1991
- Joined: Thu Jan 05, 2012 11:11 am
- Location: Grand Rapids, Michigan USA
- Contact:
Re: Volume Pot Wiring
Welcome to the MIMForum, Kelly.
Well, the solder joints don't look too good. It looks like your iron won't get things hot enough and you are ending up with "cold" solder joints on the back of that pot. Also, you don't need that short piece of red wire on the back of the pot. If the pot no longer does anything, it is because there is a connection between the two lugs with wires attached- not the one that is soldered to the back of the pot, but the other two.
Well, the solder joints don't look too good. It looks like your iron won't get things hot enough and you are ending up with "cold" solder joints on the back of that pot. Also, you don't need that short piece of red wire on the back of the pot. If the pot no longer does anything, it is because there is a connection between the two lugs with wires attached- not the one that is soldered to the back of the pot, but the other two.
- Mark Swanson, guitarist, MIMForum Staff
-
- Posts: 2
- Joined: Mon Apr 18, 2016 3:57 pm
Re: Volume Pot Wiring
Mark,
Thank you for your help! I'll pull the red wire and solder the wires again with a decent iron. Hopefully this will solve the issue.
Thank you for your help! I'll pull the red wire and solder the wires again with a decent iron. Hopefully this will solve the issue.
- Barry Daniels
- Posts: 3191
- Joined: Thu Jan 05, 2012 10:58 am
- Location: The Woodlands, Texas
Re: Volume Pot Wiring
It is possible to damage a pot with excessive heat during soldering. So you may be better off starting with a new pot.
MIMF Staff
-
- Posts: 2690
- Joined: Sat Jan 07, 2012 10:01 pm
- Location: Portland, OR
- Contact:
Re: Volume Pot Wiring
Soldering to the backs of the pots is redundant and it requires a big soldering iron (75-100W) to do it effectively. The pot cases are already grounded via the control plate.
-
- Posts: 497
- Joined: Mon Jan 09, 2012 2:02 pm
- Location: Baltimore, Maryland
Re: Volume Pot Wiring
If you're soldering to the back of a pot, it's best to clean/polish a spot on the edge where the back bends around to the side and solder there. It heats up a little faster and there's less chance of damaging the pot.
A man hears what he wants to hear, and disreguards the rest. Paul Simon
-
- Posts: 243
- Joined: Sun Jan 08, 2012 7:58 am
- Location: Massachusetts
Re: Volume Pot Wiring
If I didn't want to replace any parts (being cheap) I might disconnect everything and start from scratch, but I have decent soldering skills and tools. You should try to get rid of all those cold joints, using a solder sucker (once again good tools) and start somewhat clean. I would go to Seymour Duncan's site and download a diagram that matches what you've got as reference.
Does the volume control not work at all or does it not shut the sound off? That third lug on the volume pot doesn't look well soldered to the back off the pot and that will keep the volume from going completely off.
But the wiring there is not particularly well done. You might want to start from scratch with new parts and use this as a learning experience. New pots, a switch and a new cap won't be too much cash outlay.
Does the volume control not work at all or does it not shut the sound off? That third lug on the volume pot doesn't look well soldered to the back off the pot and that will keep the volume from going completely off.
But the wiring there is not particularly well done. You might want to start from scratch with new parts and use this as a learning experience. New pots, a switch and a new cap won't be too much cash outlay.
-
- Posts: 640
- Joined: Thu Dec 27, 2012 4:28 pm
Re: Volume Pot Wiring
A good spool of solder wick is quite helpful as well. I prefer it over the solder sucker.